XAV-602BT
55
Pin No.
Pin Name
I/O
Description
53
SELF_SW
I
Self loading position detection switch input terminal
54
IN_SW
I
Disc insert detection switch input terminal
55
D_SW
I
Chucking end detection switch input terminal
56
MECHA_RESET
O
Reset signal output to the DVD mechanism deck block “L”: reset
57
MECHA_CTS
O
Clear to send signal output to the DVD mechanism deck block
58
CDP/SDP
O
VBUS charging mode selection signal output to the USB charging controller
“L”: not current 1.5 A, “H”: current 1.5 A
59
MHL_DET
I
MHL detection signal input terminal Not used
60
VCC
-
Power supply terminal (+3.3V)
61
AP_RESET
O
Reset signal output to the panel section “L”: reset
62
VSS
-
Ground terminal
63
AP_ON
O
Power supply on/off control signal output to the DC/DC converter “H”: power on
64
ILL_IN
I
Illumination line detection signal input terminal for the automatic dimmer control
“L”: dimmer on
65
NCO
-
Not used
66
EJECT
O
Loading motor drive signal (eject direction) output terminal “H”: motor on
67
LOAD
O
Loading motor drive signal (loading direction) output terminal “H”: motor on
68
DR_ON
O
Power supply on/off control signal output terminal for loading motor driver “H”: power on
69
VMUTE
O
Video muting on/off control signal output to the video select IC “L”: muting on
70, 71
SEL_VOUT0,
SEL_VOUT1
O
Video signal selection signal output to the video select IC
72
NOSE_SW
I
Front panel connecting detection signal and error signal input from the front panel section
“L”: normal mode
73, 74
SEL_VIN0, SEL_VIN1
O
Video signal selection signal output to the video select IC
75
AP_Tx
O
Serial data output to the panel section
76
AP_Rx
I
Serial data input from the panel section
77
EN_SYS
O
Power supply on/off control signal output terminal for DC/DC converter “H”: power on
78
MHL_RST
O
MHL reset signal output terminal Not used
79
USB_ON1
O
Power supply on/off control signal output terminal for USB section “H”: power on
80
USB_OVER
I
USB over current detection signal input from the DC/DC converter “L”: over current
81
RE_0
I
Jog dial pulse input from the panel section (A phase input) (for volume)
82
RE_1
I
Jog dial pulse input from the panel section (B phase input) (for volume)
83
IDET
I
Monitor open/close motor drive current detection signal input terminal Not used
84
TEMP
I
Temperature detection signal input terminal Not used
85
KEY_IN0
I
Front panel key input terminal (A/D input)
86
RC_IN0
I
Rotary commander key input terminal (A/D input)
87
RCACK
I
Acknowledge signal (wake up signal) input terminal for the rotary commander key entry
Acknowledge signal is input to accept any function key in the standby state On at input of “H”
88
KEYACK
I
Acknowledge signal (wake up signal) input terminal for the front panel key entry
Acknowledge signal is input to accept any function key in the standby state On at input of “H”
89
RC_IN1
I
Rotary commander key input terminal
90
M_LOW
O
Monitor open/close speed (low) control signal output terminal Not used
91
M_MID
O
Monitor open/close speed (middle) control signal output terminal Not used
92
USB_ON2
O
Power supply on/off control signal output terminal for USB section “H”: power on
93
CLOSE
I
Monitor close detection switch input terminal Not used
94
AVSS
-
Ground terminal
95
MOTOR_ON
O
Power supply on/off control signal output terminal Not used
96
VREF
I
Reference voltage (+3.3V) input terminal (for A/D converter)
97
AVCC
-
Power supply terminal (+3.3V)
98
O
Monitor open/close motor drive signal (forward direction) output terminal Not used
99
MOTOR_-
O
Monitor open/close motor drive signal (reverse direction) output terminal Not used
100
NCO
-
Not used
Summary of Contents for XAV-602BT
Page 30: ...XAV 602BT 30 MEMO ...
Page 71: ...MEMO XAV 602BT 71 ...
