XAV-60/E60
64
Pin No.
Pin Name
I/O
Description
1
VCOM_AMP
O
VCOM amplitude voltage control signal output terminal
2
VCOM_BIAS
O
VCOM bias voltage control signal output terminal
3
NCO
O
Not used
4
SPEED_IN
I
Speed pulse input terminal Not used
5
NCO
O
Not used
6
BYTE
I
External data bus width selection signal input terminal Fixed at “L” (16 bit) in this set
7
FLASH_W
I
Flash writing terminal “L”: normally operation mode, “H”: writing mode
8
XCIN
I
Low-speed system clock input terminal Not used
9
XCOUT
O
Low-speed system clock output terminal Not used
10
RESET
I
Reset signal input from the master controller and reset signal generator “L”: reset
11
XOUT
O
High-speed system clock output terminal (6 MHz)
12
VSS
-
Ground terminal
13
XIN
I
High-speed system clock input terminal (6 MHz)
14
VCC1
-
Power supply terminal (+3.3V)
15
NMI
I
Non-maskable interrupt signal input terminal Fixed at “H” in this set
16
MASTER_IF
I
Communication start signal input from the master controller
17
CPV
I
Vertical sync signal input from the video processor
18
PHOTO
I
Monitor open/close photo detection signal input terminal Not used
19
NCO
O
Not used
20
VISUAL_RX
I
Serial data input from the master controller
21
NCO
O
Not used
22
VISUAL_TX
O
Serial data output to the master controller
23
BT_IND
O
LED drive signal output terminal for Bluetooth indicator Not used
24
KEY_PWM
O
LED drive signal output terminal for front panel key illumination
25
BL_ENA
O
LED drive signal output to the backlight controller for liquid crystal display back light
“H”: LED on
26
BL_PWM
O
Dimmer control signal output to the backlight controller for liquid crystal display back light
27
I2CKO
O
I2C clock signal output to the video decoder
28
I2SIO
I/O
Two-way I2C data bus with the video decoder
29
FLASH_TX
O
Serial data output to the fl ash writing connector
30
FLASH_RX
I
Serial data input from the fl ash writing connector
31
F_CLK
O
Serial data transfer clock signal output terminal at the fl ash writing mode
32
BUSY
O
Busy signal output terminal at the fl ash writing mode
33
NAVI_TX
O
Serial data output to the EXT connector for external navigation
(E (PAL) and Saudi Arabia models only)
34
NAVI_RX
I
Serial data input from the EXT connector for external navigation
(E (PAL) and Saudi Arabia models only)
35
NAVI_DET
I
External navigation detection signal input terminal “L”: navigation is detected
(E (PAL) and Saudi Arabia models only)
36
NAVI_RTS
O
Request to send signal output terminal for navigation Not used
37
BL_STATUSP
I
Power converter status input from the backlight controller
38
BL_STATUSL
I
LED operation status input from the backlight controller
39
HOLD
I
External data bus terminal at the fl ash writing mode Fixed at “L” in this set
40
DEC_GPIO_1
I
Non-input signal detection signal input from the video decoder
“L”: non-input signal is detected
41
DEC_GPIO_2
O
Not used
42
DEC_RST
O
Reset signal output to the video decoder “L”: reset
43
NCO
O
Not used
44
WRI/WR
I
External data bus terminal at the fl ash writing mode Fixed at “H” in this set
45 to 47
NCO
O
Not used
48
NAVI_CTS
I
Clear to send signal input terminal for navigation Not used
49
MOTOR_ON
O
Power supply on/off control signal output terminal for monitor open/close motor driver
Not used
50
NCO
O
Not used
51
M_LOW
O
Monitor open/close speed (low) control signal output terminal Not used
52
M_MID
O
Monitor open/close speed (middle) control signal output terminal Not used
53
OPEN
I
Monitor open detection switch input terminal
54
CLOSE
I
Monitor close detection switch input terminal
55
MOTOR+
O
Monitor open/close motor drive signal (forward direction) output terminlal Not used
56
MOTOR–
O
Monitor open/close motor drive signal (reverse direction) output terminal Not used
VISUAL BOARD IC2001 RF3640DDZ95FB (VISUAL CONTROLLER)
Ver. 1.1
Summary of Contents for XAV-60 - 6.1 Inch Avc
Page 92: ...92 XAV 60 E60 MEMO ...
