1-4
WRT-807B (U/CE)
7
(GB)
1
234
BA
T
T
indication
Lights
L
ights
F
lashes
Goes of
f
Batter
y
condition
Good
Less than
half-charge
Almost
exhausted
Completely
exhausted
2
1,3
E
e
P
o
wer Suppl
y
The microphone can operate on one LR6 (size AA) alkaline
battery continuously for about 5 hours at 25
ºC (77
ºF).
Inser
ting the
batter
y
1
T
urn
the grip in the direction of the arrow to open the
battery holder
.
2
Match the battery to the polarity markings and insert it
into the battery holder
.
3
Close the battery holder and lock the grip by turning it
in the opposite direction of the arrow
.
Batter
y indication
When you turn the power on, the battery condition is
indicated by the BA
TT
indication in the liquid-crystal
display
.
Note
The indication may be incorrect if the battery was not new
when inserted. If you plan to use the microphone for a long
period, replace the battery with a new one.
8
(GB)
Channel selection
mode
*
Freqency selection
mode
Attenuator adjustment
mode
Accumulated time
indication reset mode
Press the
SET
button.
Display example
for CE62 model
Settings
Initiating Setting Mode
Enter Setting mode to change the transmitting channel, the
transmitting frequency and the attenuation level, or to reset
the accumulated battery use time indication.
T
o
enter Setting mode
While holding down the SET
button, turn the POWER
switch to ON.
Hold the SET
button down until an indication appears on the
liquid-crystal display
.
The microphone enters Setting mode and the indication
before the microphone was previously turned OFF flashes
on the liquid-crystal display
.
Pressing the SET
button cycles the modes in the order of
Channel selection mode, Frequency selection mode (page
9), Attenuator adjustment mode (page 10) and Accumulated
time indication reset mode (see page 1
1).
Note
On the model available in Europe, the transmitting channels
are grouped in four sets as shown in
“Sony W
ireless
Microphone System Frequency List.
”
*
On the model available in Europe, set the channel group indication (the
left two digits) first. Press the + or
–
button to toggle the channel
group (e.g., for CE62 model: 00
y
62
y
63
y
64) and press the
SET
button. Then, the remaining four digits start to flash for setting
the channel number
.
Changing the T
ransmitting
Channel
The transmitting channel can be selected through either the
channel number or the frequency
.
1
Set the microphone to Setting mode.
If the channel number (or frequency) indication does not
appear
,
(or
press the SET
button until the channel number
frequency) indication appears.
9
(GB)
Channel selection mode
Freqenc
y
selection mode
+ button
–
button
+ button
–
button
Display example for CE62 model
2
Press the + or
–
button to select the channel number (or
frequency).
Pressing the + button cycles the indication in the order
shown in separate
“Sony W
ireless
Microphone System
Frequency List.
” Pressing the
–
button cycles the
indications in the opposite direction.
Hold down the button to change the channel number (or
frequency) quickly
.
3
When the desired channel number (or frequency)
appears, turn the POWER switch to OFF to release
Setting mode, or press the SET
button to continue
operations in Setting mode.
The next time you turn on the microphone (by turning the
POWER switch to ON), the microphone will enter T
ransmit
mode with the selected channel number (or frequency).
Notes
•
The microphone cannot transmit in Setting mode.
•
Make sure that the channel selected on the microphone is
the same as that selected on the tuner being used in the
same system.
•
Depending on the noise or interference conditions, all
selectable channels may not be usable. If necessary
,
you
can determine which channels are usable by cycling the
channel selection through a number of channels on the
tuner with the microphone set to OFF
.
Those channels for
which the RF indicator on the tuner does not light are
usable.
•
The microphone may not operate correctly if it is turned
on immediately after being turned of
f
in Setting mode.
W
ait for
a
few
W
ait for a few seconds before turning the power on again.
10
(GB)
+ button
AF
RF
BA
TT
AF
RF
BA
TT
–
button
Changing the Input Atten
uation
Setting
The input attenuation setting can be changed within a range
of 0 dB to 21 dB (in 3-dB steps) in either Setting mode or
T
ransmit mode.
Changing the input atten
uation
in Setting
mode
1
Set the microphone to Setting mode.
2
If the attenuation level is not displayed, press the SET
button until it appears.
3
Press the + or
–
button to change the attenuation setting.
Hold down the button to change the level quickly
.
4
Once the desired level appears, turn the POWER switch
to OFF to release Setting mode, or press the SET
button
to continue operations in Setting mode.
The next time you turn on the microphone (by turning the
POWER switch to ON), the microphone enter
T
ransmit
mode with the selected attenuation setting.
Changing the input atten
uation
in T
ransmit
mode
Y
ou can also change the input attenuation setting while
transmitting
If
button
in T
ransmit
mode.
1
the attenuation level is not displayed, press the SET
until it appears.
2
Press the + or
–
button to change the attenuation setting.
Setting
Summary of Contents for WRT-807B
