7
Main specifications
Trouble-shooting guide
A/D Converter
Maximum input level:
+24 dBu
Adjustable gain range:
30 dB
Quantization:
24 bit
Dynamic range:
(A-weight, 24 bit)
113 dB or more
(A-weight, 20 bit)
110 dB or more
(A-weight, 16 bit)
95 dB or more
Total harmonic distortion rate:
(–10 dBFS 20 Hz – 20 kHz, 24 bit)
0.005 % or less
Frequency response:
(48 kHz Fs) 20 – 20,000 Hz
–0.5
0
dB
Sampling frequency:
44.1/48 kHz
Word length:
16, 20, 24 bit
Input connector:
XLR3-31 type, 2 pin Hot
Impedance:
18 k
Ω
Output connector:
AES/EBU, IEC958
External Sync Input/Output
Lockup frequency:
44.1/48 kHz
Input/output connector: BNC, XLR type (AES/EBU)
Output impedance (BNC):
75
Ω
or more
D/A Converter
Maximum output range: +24 dBu
S/N ratio:
(A-weight, 24/20 bit)
118 dB or more
Total harmonic distortion rate:
(–10 dBFS 20 Hz – 20 kHz,
22 kHz LPF) 0.008 % or less
Frequency response:
(48 kHz Fs) 20 – 20,000 Hz
–0.5
0
dB
Input sampling frequency:
32 – 48 kHz
Input word length:
16 – 24 bit
Quantization:
20 bit
Input connector:
AES/EBU, IEC958
Output connector:
XLR3-32 type, 2 pin Hot
Load impedance:
600
Ω
or more
Conversion delay time:
(Analog input/output,
48 kHz Fs) approx. 2.0 msec
Power requirements:
AC 120/230 V, 50/60 Hz
Power consumption:
20 W
Operating temperature range:
0 – 40 °C
Storage temperature range:
–20 – +60 °C
Mass:
approx. 6 kg (13.2 lbs.)
Dimensions:
approx. 482
×
44
×
350 mm
(19.0
×
1.7
×
13.8 in.) (w
×
h
×
d)
excluding the projecting parts
Supplied accessories:
Plug adaptor (1), Operating
Instructions (1)
In order to improve our products, the specifications and
external appearance are subject to change without prior
notice.
In the event of any unexpected problems, please read this manual thoroughly and check the following points before calling
for repairs. If after that, normal operation cannot be resumed, consult your nearest Sony dealer.
Condition
Synchronizing the digital input (DIGITAL INPUT) puts certain
sources out of sync.
External synchronization from WORD SYNC input (BNC) does
not work.
The D/A output level is too high.
Causes / Solutions
•
A digital signal that has been subjected to a pitch control
that alters the sampling frequency has been supplied.
(This unit does not support a pitch control that alters the
sampling frequency.)
•
An unsupported sampling frequency has been supplied.
•
A sync signal with a sampling frequency other than
48 kHz and 44.1 kHz has been supplied.
(This unit does not support sampling frequencies, such
as 32 kHz.)
•
This unit has a D/A output level of +24 dBu in relation
to 0 dBFS. See
8
on page 5.
Block diagram/Dimensions/
Main specifications/
Trouble-shooting guide
Summary of Contents for SRP-DC5
Page 8: ...8 Printed in Japan ...
