Sony SpectaProof UP-D9500 Instructions For Use Manual Download Page 11

Page: 11 / 48

Introduction

Rear

AC Inlet
Connect the supplied power cord here.

DIP Switch
Determines the SCSI device ID number of the
printer, and sets the internal terminator on or
off.

SCSI Connectors (50-pin, half pitch)
Connect the computer to control the printer
and other SCSI devices with SCSI cables. If
only one of the SCSI connectors on the printer
is used, the internal terminator should be
enabled by the DIP switch.

10BASE 5 Connector
The printer may be connected to an Ethernet
network by 10BASE 5 cable connected here.

10BASE-T Connector
The printer may be connected to an Ethernet
network by 10BASE-T cable connected here.

LocalTalk Connector
The printer may be connected to an AppleTalk
network with a LocalTalk cable connected
here.

Parallel Interface Connector
(36-Pin Amphenol)
When the printer is controlled via a PC
parallel port, the parallel printer cable connects
here.

Summary of Contents for SpectaProof UP-D9500

















































Search results

Summary of Contents for SpectaProof UP-D9500

Reviews:

Related manuals for SpectaProof UP-D9500

Brands by name

Popular brands

Sony SpectaProof UP-D9500, Instructions For Use Manual

Search results

Summary of Contents for SpectaProof UP-D9500

Reviews:

Related manuals for SpectaProof UP-D9500

Brands by name

Popular brands