Installation
Caution
To prevent the camera from falling, make sure to attach the supplied wire
rope.
Suitable lens
The lens must be a CS-mount type and the protrusion behind the mounting
surface must be 5.5 mm (
7/32
inch) or less.
Caution
When you install it into a wall or a ceiling, check that the wall or the ceiling
ˎ
is strong enough to hold the weight of the camera including the mounting
bracket, and install it without fail. If not, the camera falls down and causes
a serious injury.
Also, check if the mounting is not loosened at least once a year. Make the
checking interval short according to use condition.
Performance will depend on the installation environment and the lens
ˎ
itself. For details, contact your authorized Sony dealer.
Attaching the wire rope
When you install the camera on a ceiling or a high position, be sure to attach the
supplied wire rope to prevent the camera from falling.
Attach the wire rope to the screw hole on the rear of the camera, as in the
illustration.
Note
Take care not to short-circuit the power terminal or the cable with the wire rope
when you attach it.
1
Secure the wire rope to the junction box on the ceiling.
Use a screw to match the screw hole of your junction box (not supplied).
2
Secure the wire rope to the wire rope mounting screw hole on the rear of
the camera using the supplied screw.
Caution
Use the supplied screws for installation. If not, the wire rope may not function
properly.
Adjusting the Camera Coverage and Focus
1
Loosen the zoom ring locking screw to adjust the camera shooting
coverage.
2
Tighten the locking screw to fix the zoom.
3
Loosen the focus ring locking screw to adjust the focus.
4
Tighten the locking screw to fix the focus.
5
Press the Easy Focus button on the rear to automatically adjust the
focus.
Note
You may not achieve satisfactory focus with the Easy Focus button due to the
shooting environment.
In this condition, press and hold Easy Focus button for more than 4 seconds to
return to the default flange back position. Then, adjust the focus following
step 3 and 4.
Connection
Connecting to the Network
Connect the network cable of the camera to a router or hub in the network using
the network cable.
Connecting the Power Source
There are three ways to supply power to this camera, as follows.
12 V DC
ˎ
24 V AC
ˎ
Power supply equipment pursuant to IEEE802.3af (PoE* system)
ˎ
*PoE stands for Power over Ethernet.
Note
Do not connect the power input cable if power is supplied by a PoE system.
Connecting to 12 V DC or 24 V AC source
Connect the power input cable of the camera to a 12 V DC or 24 V AC source.
Use a 12 V DC or 24 V AC source isolated from 100 to 240 V AC. The acceptable
ˎ
voltage ranges for each are as follows.
12 V DC: 10.8 V to 13.2 V
24 V AC: 19.2 V to 28.8 V
- In the USA, The product shall be powered by a UL Listed Class 2 Power
Supply Only.
- In Canada, The product shall be powered by a CSA certified Class 2 Power
Supply Only.
Use UL cable (VW-1 style 10368) for these connections.
ˎ
Recommended cable
12 V DC:
CABLE(AWG)
#24
#22
#20
Max. length(m(feet))
8 (26.2)
14 (45.9)
20 (65.5)
24 V AC:
CABLE(AWG)
#24
#22
#20
Max. length(m(feet))
11 (36.1)
19 (62.3)
28 (91.9)
Connecting to the power supply equipment pursuant
to IEEE802.3af
The power supply equipment pursuant to IEEE802.3af supplies the power
through the network cable. For details, refer to the Instruction Manual of the
equipment.
Specifications
Compression
Video compression format
JPEG/H.264
Audio compression format
G.711/G.726/AAC
Maximum frame rate
SNC-VB600/VB630
60 fps
SNC-VB600B
30 fps
Camera
Signal system
NTSC color system/PAL color system
(switchable)
Image device
SNC-VB600/VB600B
1/3type CMOS (Exmor)
Effective picture elements:
Approx. 1,370,000
SNC-VB630
1/2.9type CMOS (Exmor)
Effective picture elements:
Approx. 2,140,000
Synchronization
Internal synchronization
Horizontal resolution
SNC-VB600/VB600B: 600 TV lines (analog video)
SNC-VB630: 700 TV lines (monitor display ratio
4:3)
Video S/N
More than 50 dB (Auto gain control maximum
rate 0 dB)
Minimum illumination
F1.2/View-DR Off/VE* Off/Auto gain control
maximum rate MAX/50 IRE (IP)/30 fps
SNC-VB600/VB600B
Color: 0.05 lx
Black & White: 0.04 lx
SNC-VB630
Color: 0.10 lx
Black & White: 0.07 lx
* VE stands for Visibility Enhancer.
Lens
Focal length
2.8 mm ~ 8 mm
Maximum relative aperture
F1.2 ~ F1.95
View angle*
SNC-VB600/VB600B: 1280 × 1024 (aspect ratio
5:4)
Vertical: 78.1° ~ 28.6°
Horizontal: 100.0° ~ 35.7°
SNC-VB630: 1920 × 1080 (aspect ratio 16:9)
Vertical: 60.6° ~ 22.5°
Horizontal: 114.2° ~ 40.0°
* The view angle will change, depending on the setting of the aspect ratio
resolution.
Minimum object distance
300 mm
Interface
LAN (PoE)
10BASE-T/100BASE-TX, auto negotiation (RJ-45)
C
CS-mount lens
5.5 (7/32) or less
Unit: mm (inch)
D
Screw (supplied)
Wire rope (supplied)
E
1,2
3,4
5
F
Front
Side
Unit: mm (inches)
72 (2 7/8)
145 (5 3/4)
44 (1 3/4)
55 (2 1/4)
54.1 (2 1/4)
150.5 (6)
62 (2 7/16)
63 (2 1/2)
I/O port
Sensor input: × 2, make contact, break contact
Alarm output: × 2, 24 V AC/DC, 1 A max.
(mechanical relay outputs electrically isolated
from the camera)
SD memory card slot
Video output
VIDEO OUT: BNC, 1.0 Vp-p, 75 ohms,
unbalanced, sync negative
Microphone input*
Minijack (monaural)
Plug-in-power supported (rated voltage: 2.5 V
DC)
Recommended load impedance: 2.2 kΩ
Line input*
Minijack (monaural)
* The microphone input and the line input are switchable with operating menu.
Line output
Minijack (monaural), Maximum output level:
1 Vrms
Others
Power supply
12 V DC ± 10%
24 V AC ± 20%, 50 Hz/60 Hz
IEEE802.3af compliant (PoE system)
Power consumption
6.0 W max.
Operating temperature
Start temperature: 0°C to 50°C (32°F to 122°F)
Working temperature: –10°C to +50°C
(14°F to 122°F)
Storage temperature
–20°C to +60°C (–4°F to +140°F)
Operating humidity
20% to 80%
Storage humidity
20% to 95%
Dimensions (w/h/d)
72 mm × 63 mm × 145 mm (2
7
/
8
inches ×
2
1
/
2
inches × 5
3
/
4
inches) not including the
projecting parts and lens
Mass
Approx. 565 g (1 lb 3.9 oz) with lens
Supplied accessories
CD-ROM (Supplied programs) (1)
Wire rope (1)
Screw M4 (1)
DC 12 V/AC 24 V connector (1)
Safety Regulations (1)
Installation Manual (this document) (1)
Design and specifications are subject to change without notice.
