Sony SLV-X9G Operating Instructions Manual Download Page 14

Page: 14 / 96

Connecting the VCR

Step 3 : Connecting the VCR

If your TV has a Scart (EURO-AV) connector, see page 15.

• Connection to your TV with an aerial cable only, see this page.
• Connection to your TV and Set-Top Box, see page 17.

If your TV does not have a Scart (EURO-AV) connector

Note

• When you connect the VCR and your TV only with an aerial cable, you have to

tune your TV to the VCR (see page 21).

Disconnect the aerial cable from
your TV and connect it to
AERIAL IN on the rear panel of
the VCR.

Connect AERIAL OUT of the
VCR and the aerial input of your
TV using the supplied aerial cable.

Connect the mains lead to the mains.

Mains lead

AERIAL IN

to mains

Aerial cable (supplied)

AERIAL OUT

: Signal flow

AERIAL IN

AERIAL

ANTENNE

ENTREE

OUT

SORTIE

ENTREE

OUT

SORTIE

AERIAL

ANTENNE

Summary of Contents for SLV-X9G

































































































Search results

Summary of Contents for SLV-X9G

Reviews:

Related manuals for SLV-X9G

Brands by name

Popular brands

Sony SLV-X9G, Operating Instructions Manual

Search results

Summary of Contents for SLV-X9G

Reviews:

Related manuals for SLV-X9G

Brands by name

Popular brands