Sony SLV-X9G Operating Instructions Manual Download Page 15

Page: 15 / 96

Connecting the VCR

tting Star

If your TV has a Scart (EURO-AV) connector

Note

• If the TV is connected to the LINE-1 (TV) connector, setting the RF channel to

OFF is recommended. In the OFF position, only the signal from the aerial is
output through the AERIAL OUT connector (see page 22).

Disconnect the aerial cable from
your TV and connect it to
AERIAL IN on the rear panel of
the VCR.

Connect AERIAL OUT of the
VCR and the aerial input of your
TV using the supplied aerial cable.

Connect LINE-1 (TV) on the VCR
and the Scart (EURO-AV)
connector on the TV with the
optional Scart cable.

This connection improves picture
and sound quality. Whenever you
want to watch the VCR picture,
press

TV/VIDEO to display

the VIDEO indicator in the
display window.

Connect the mains lead to the mains.

Mains lead

LINE-1

(TV)

AERIAL IN

Scart
(EURO-AV)

to mains

Aerial cable (supplied)

AERIAL OUT

: Signal flow

Scart cable (not supplied)

AERIAL IN

AERIAL

ANTENNE

ENTREE

OUT

SORTIE

ENTREE

OUT

SORTIE

AERIAL

ANTENNE

continued

Summary of Contents for SLV-X9G

































































































Search results

Summary of Contents for SLV-X9G

Reviews:

Related manuals for SLV-X9G

Brands by name

Popular brands

Sony SLV-X9G, Operating Instructions Manual

Search results

Summary of Contents for SLV-X9G

Reviews:

Related manuals for SLV-X9G

Brands by name

Popular brands