Sony SLV-X9G Operating Instructions Manual Download Page 21

Page: 21 / 96

Tuning your TV to the VCR

tting Star

Step 5 : Tuning your TV to the VCR

If your TV has a Scart (EURO-AV) connector, see page 22.

If your TV does not have a Scart (EURO-AV) connector

Follow the steps below so that your TV will properly receive the video
signals from your VCR.

Press RF CHANNEL on the VCR lightly.

The currently set RF channel appears in the display window.

The VCR signal is output through this channel to the TV.

Turn on your TV and select a programme position for the VCR
picture.

This programme position will now be referred to as the video
channel.

Tune the TV to the same channel
shown in the VCR display window so
that the picture on the right appears
clearly on the TV screen.

Refer to your TV manual for TV
tuning instructions.

If the picture does not appear clearly,
see “To obtain a clear picture from the
VCR” below.

P/–

RF CHANNEL

AUTO

SET UP

RF CHANNEL

SONY VIDEO CASSETTE RECORDER

continued

Summary of Contents for SLV-X9G

































































































Search results

Summary of Contents for SLV-X9G

Reviews:

Related manuals for SLV-X9G

Brands by name

Popular brands

Sony SLV-X9G, Operating Instructions Manual

Search results

Summary of Contents for SLV-X9G

Reviews:

Related manuals for SLV-X9G

Brands by name

Popular brands