Sony SLV-X827MN Operating Instructions Manual Download Page 7

Page: 7 / 58

Getting Started

SLV-X827MN 3-858-297-11 (1)

Getting Started

Manufacturer

Code number

Sinudyne

TEAC

Telefunken

Thomson

43*

Toshiba

White
Westinghouse

Manufacturer

Code number

Saba

12,13

Samsung

22,23

Sanyo

Schneider

Seleco

Sharp

Siemens

You can use the WIDE button after entering a code number with any of the
following marks;

: Press WIDE to switch the wide picture mode on or off.

: Press WIDE, then press VOL+/– to select the wide picture mode you

want.

: Press WIDE. The menu appears on the TV screen. Then, press CURSOR

to select the wide picture you want and press EXECUTE.

Notes

• If the TV uses a different remote control system from the one programmed to work

with the VCR, you cannot control your TV with the remote commander.

• If you enter a new code number, the code number previously entered will be erased.
• When you replace the batteries of the remote commander, the code number

automatically resets to 01 (Sony). Reset the appropriate code number.

Summary of Contents for SLV-X827MN



























































Search results

Summary of Contents for SLV-X827MN

Reviews:

Related manuals for SLV-X827MN

Brands by name

Popular brands

Sony SLV-X827MN, Operating Instructions Manual

Search results

Summary of Contents for SLV-X827MN

Reviews:

Related manuals for SLV-X827MN

Brands by name

Popular brands