Sony SLV-X827MN Operating Instructions Manual Download Page 46 | Manualshive

Page: 46 / 58

background image

Additional Operations

46

SLV-X827MN 3-858-297-11 (1)

About Adaptive Picture Control (APC)

Adaptive Picture Control (APC) automatically
improves recording and playback quality by
adjusting the VCR to the condition of the video
heads and tape. To maintain better picture quality,
we recommend that you set APC to ON in the SET
UP MENU (with the APC indicator in the display
window lit).

APC playback

The APC function automatically works on all types of tapes, including rental
tapes and tapes that were not recorded with APC.

APC recording

Whenever you insert a tape and first start recording, the VCR adjusts to the
tape using the APC function (the APC indicator flashes rapidly). This
adjustment is retained until the tape is ejected.

To deactivate the APC

Press MENU and select SET UP MENU, then set APC to OFF. The APC
indicator in the display window goes off.

Note

• There is a delay of a few seconds before the VCR actually starts recording while the

VCR analyses the tape. To avoid the delay, first set the VCR to recording pause (the
APC indicator flashes slowly) and press

r

REC to have the VCR analyse the tape

(the APC indicator flashes rapidly). After the APC indicator stops flashing, press

P

PAUSE to start recording immediately. If you want to start recording quickly

without using the APC function, first set the VCR to recording pause (the APC
indicator flashes slowly) and press

P

PAUSE to start recording.

Adjusting the picture

Adjusting the tracking

Although the VCR automatically adjusts the tracking when playing a tape
(the tracking indicator

flashes in the display window, then goes off),

distortion may occur if the tape was recorded in poor condition. If so,
manually adjust the tracking.

Press the TR/– buttons to display the
tracking meter. The distortion should disappear as
you press one of the two buttons (The

indicator

lights up). To resume automatic tracking adjustment,
eject the tape and reinsert it.

Tracking meter

NORMAL TRACKING

SET UP MENU

DIMMER

BUZZER

HIFI AUDIO

STD

NICAM

AUDIO MIX

ON

OFF

ON

OFF

ON

OFF

SET

:

SELECT

:

APC

ON

OFF

«
...
44
45
46
47
48
...
»

Summary of Contents for SLV-X827MN



























































Reviews:

No comments

Related manuals for SLV-X827MN

Brand: Symphonic Pages: 8

Brand: Symphonic Pages: 32

Brand: Symphonic Pages: 32

Brand: Symphonic Pages: 68

Brand: THOMSON Pages: 26

Brand: THOMSON Pages: 26

Brand: THOMSON Pages: 26

Brand: THOMSON Pages: 32

Brand: RCA Pages: 36

TruFlat T27TF668

Brand: RCA Pages: 56

Brand: Tech Line Pages: 68

Brand: Daewoo Pages: 56

Brand: Zenith Pages: 29

Brand: Samsung Pages: 50

AGTL950 - TIME LAPSE VCR

Brand: Panasonic Pages: 58

Omnivision PV-M2089

Brand: Panasonic Pages: 49

Brand: Hitachi Pages: 43

Brand: Panasonic Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands