Sony SLV-X827MN Operating Instructions Manual Download Page 51

Page: 51 / 58

Additional Information

SLV-X827MN 3-858-297-11 (1)

Recor

ding

Symptom

No TV programmes appear
on the TV screen.

TV reception is poor.

The tape starts playing as soon
as it is inserted.

The tape is ejected when you
press

REC.

Nothing happens when you
press

REC.

The timer does not operate.

No tape can be inserted.

The remote commander does
not function.

You cannot control other TVs.

The tracking indicator does not
appear on the screen.

The VCR needs to be cleaned.

imer r

ecording

Others

Remedy

• Make sure the TV is set to the video channel. If you are

using a monitor, set it to video input.

• Adjust the TV aerial.
• Make sure SYSTEM (B/G or D/K) in the TUNER

PRESET menu is set to the system in your area.

• The safety tab has been removed. To record on this

tape, cover the tab hole.

• Check that the safety tab has not been removed.

• Make sure the tape is not at its end.
• Select the correct source with the INPUT SELECT

button. Select a programme position when recording
TV programmes; select “L1” or “L2” when recording
from other equipment.

• Check that the clock is set.
• Make sure a tape has been inserted.
• Check that the safety tab has not been removed.
• Make sure the tape is not at its end.
• Make sure a programme has been set for timer

recording.

• Make sure your timer settings have not already passed

the current time.

• Check that the satellite tuner is turned on.
• The clock stops if the VCR is disconnected from the

mains for more than an hour. Reset the clock and timer.

• Check that a tape isn’t already in the tape

compartment.

• Make sure you are pointing the remote commander at

the remote sensor on the VCR.

• Replace all the batteries in the remote commander with

new ones if they are weak.

• Make sure the TV / VIDEO remote control switch is

set correctly.

• Set your TV’s code number. The code number resets to

01 when you replace the batteries of the remote
commander.

• The recording condition of the tape is very poor and

tracking cannot be adjusted, or the NTSC system is
being used.

• Clean the cabinet, panel and controls with a dry, soft

cloth, or a soft cloth slightly moistened with a mild
detergent solution. Do not use any type of solvent,
such as alcohol or benzine.

Summary of Contents for SLV-X827MN



























































Search results

Summary of Contents for SLV-X827MN

Reviews:

Related manuals for SLV-X827MN

Brands by name

Popular brands

Sony SLV-X827MN, Operating Instructions Manual

Search results

Summary of Contents for SLV-X827MN

Reviews:

Related manuals for SLV-X827MN

Brands by name

Popular brands