Sony SLV-SE100A1, SLV-SE100A2 Operating Instructions Manual Download

Page: 9 / 92

Getti

ng Sta

rted

Connecting the VCR

Step 3 : Connecting the VCR

If your TV has a Scart (EURO-AV) connector, see page 10.

If your TV does not have a Scart (EURO-AV) connector

Note

• When you connect the VCR and your TV only with an aerial cable, you have to tune your TV

to the VCR (see page 13).

Disconnect the aerial cable from your
TV and connect it to AERIAL IN on
the rear panel of the VCR.

Connect AERIAL OUT of the VCR
and the aerial input of your TV using
the supplied aerial cable.

Connect the mains lead to the mains.

Mains lead

AERIAL IN

to mains

Aerial cable (supplied)

AERIAL OUT

: Signal flow

AERIAL IN

AERIAL

ANTENNE

ENTREE

OUT

SORTIE

AERIAL

ANTENNE

ENTREE

OUT

SORTIE

continued

Summary of Contents for SLV-SE100A1, SLV-SE100A2





























































































Search results

Summary of Contents for SLV-SE100A1, SLV-SE100A2

Reviews:

Related manuals for SLV-SE100A1, SLV-SE100A2

Brands by name

Popular brands

Sony SLV-SE100A1, SLV-SE100A2, Operating Instructions Manual

Search results

Summary of Contents for SLV-SE100A1, SLV-SE100A2

Reviews:

Related manuals for SLV-SE100A1, SLV-SE100A2

Brands by name

Popular brands