Sony SLV-SE100A1, SLV-SE100A2 Operating Instructions Manual Download

Page: 10 / 92

Connecting the VCR

If your TV has a Scart (EURO-AV) connector

Note

• If the TV is connected to the LINE-1 (TV) connector, setting the RF channel to OFF is

recommended. In the OFF position, only the signal from the aerial is output through the
AERIAL OUT connector (see page 15).

Disconnect the aerial cable from your
TV and connect it to AERIAL IN on
the rear panel of the VCR.

Connect AERIAL OUT of the VCR
and the aerial input of your TV using
the supplied aerial cable.

Connect LINE-1 (TV) on the VCR
and the Scart (EURO-AV) connector
on the TV with the optional Scart
cable.

This connection improves picture and
sound quality. Whenever you want to
watch the VCR picture, press

TV/

VIDEO to display the VIDEO
indicator in the display window.

Connect the mains lead to the mains.

Mains lead

LINE-1

(TV)

AERIAL IN

Scart (EURO-AV)

to mains

Aerial cable (supplied)

AERIAL OUT

: Signal flow

Scart cable (not supplied)

AERIAL IN

AERIAL

ANTENNE

ENTREE

OUT

SORTIE

AERIAL

ANTENNE

ENTREE

OUT

SORTIE

Summary of Contents for SLV-SE100A1, SLV-SE100A2





























































































Search results

Summary of Contents for SLV-SE100A1, SLV-SE100A2

Reviews:

Related manuals for SLV-SE100A1, SLV-SE100A2

Brands by name

Popular brands

Sony SLV-SE100A1, SLV-SE100A2, Operating Instructions Manual

Search results

Summary of Contents for SLV-SE100A1, SLV-SE100A2

Reviews:

Related manuals for SLV-SE100A1, SLV-SE100A2

Brands by name

Popular brands