Sony SLV-M10HF - Video Cassette Recorder Operating Instructions Manual Download | Manualshive

Page: 6 / 120

background image

6

Getting Started

Setting the COMMAND MODE switch

To remotely control the VCR with
the remote commander, set
COMMAND MODE on the
remote commander to the same
position as that on the VCR.
Usually set to VTR 3. Change the
position as shown below to
control other Sony VCRs:

VTR 1

: For Sony Betamax format VCRs

VTR 2

: For Sony 8mm format VCRs

VTR 3

: For Sony VHS format VCRs

To change the command mode
position of the VCR, press and
hold COMMAND MODE on the
VCR for about two seconds and
repeat until the desired position
appears in the display window.

Controlling other TVs with the remote commander

The remote commander is preprogrammed to control non-Sony TVs. If your TV
is listed in the table below, set the appropriate manufacturer’s code number.

1

Set TV / VIDEO at the top of the remote commander to TV .

2

Hold POWER down, and enter your TV’s code number(s) using the
number buttons. Then release POWER.

Now you can use the POWER, VOL +/–, CH +/–, and TV/VIDEO buttons to
control your TV. You can also use the buttons marked with a dot (•) to
control a Sony TV. To control the VCR, reset TV / VIDEO to VIDEO .

Tip

• If you set your TV’s code number correctly while the TV is turned on, the TV turns

off automatically.

COMMAND
MODE

Step 2: Setting up the remote commander (continued)

COMMAND MODE

VTR

3

1

2

3

4

5

6

«
...
4
5
6
7
8
...
»

Summary of Contents for SLV-M10HF - Video Cassette Recorder

























































































































Reviews:

No comments

Related manuals for SLV-M10HF - Video Cassette Recorder

Brand: Aiwa Pages: 105

Brand: Panasonic Pages: 34

AG5210P - HI-FI VIDEO RECORDER

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 2

AG5210 - VIDEO CASSETTE RECORDER

Brand: Panasonic Pages: 16

AG7450AP - HI-FI VCR/BRC

Brand: Panasonic Pages: 26

NV-HD650 Series

Brand: Panasonic Pages: 106

Brand: Panasonic Pages: 40

Brand: Panasonic Pages: 51

Brand: Panasonic Pages: 52

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 73

Brand: Panasonic Pages: 80

Brand: Panasonic Pages: 68

AG-DV2500 - Professional Video Cassete recorder/player

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 86

Brand: Panasonic Pages: 80

AGDTL1P - TIME LAPSE RECORDER

Brand: Panasonic Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands