Sony SLV-M10HF - Video Cassette Recorder Operating Instructions Manual Download

Page: 54 / 120

Basic Operations

To skip playback

You can skip a portion of playback you don‘t want to watch such as a
commercial and restart playback by pressing a single button.

Press SMART CUE during playback of the scene you want to skip. The
VCR starts searching.

Press SMART CUE again when you find the scene you want to watch.
The VCR stops searching, rewinds a few seconds, then resumes normal
playback.

If you press and hold SMART CUE while the VCR is skip searching, the VCR
will stop searching, and continue rewinding until you release SMART CUE.

Tip

• You can change the length of rewinding time on the ADVANCED OPTIONS menu.

See page 83.

To use the time counter

At the point on the tape that you want to find later, press COUNTER RESET.
The counter in the display window resets to “0:00:00.” Search for the point
afterwards by referring to the counter.

To display the counter on the TV screen, press DISPLAY.

Notes

• Tapes recorded in the LP mode on other VCRs can be played back on this VCR but

the picture quality cannot be guaranteed.

• The counter resets to “0:00:00” whenever a tape is reinserted.
• The counter stops counting when it comes to a portion with no recording.

Stop play

Pause play

Resume play after pause

Fast-forward the tape

Rewind the tape

Eject the tape

Additional tasks

Press

STOP

PAUSE

PAUSE or

PLAY

)

FF during stop

REW during stop

EJECT

Playing a tape (continued)

VIDEO

Summary of Contents for SLV-M10HF - Video Cassette Recorder

























































































































Search results

Summary of Contents for SLV-M10HF - Video Cassette Recorder

Reviews:

Related manuals for SLV-M10HF - Video Cassette Recorder

Brands by name

Popular brands

Sony SLV-M10HF - Video Cassette Recorder, Operating Instructions Manual

Search results

Summary of Contents for SLV-M10HF - Video Cassette Recorder

Reviews:

Related manuals for SLV-M10HF - Video Cassette Recorder

Brands by name

Popular brands