Sony SLV-669HF Operating Instructions Manual Download Page 48

Page: 48 / 68

Additional Operations

Normal recording

0:30

1:00

5:30

6:00

REC

Setting the
recording
duration time

After starting recording in the normal
way, you can have the VCR stop
recording automatically after a specified
duration.

While recording, press

REC.

The indicator appears in the display window.

Press

REC repeatedly to set the duration.

Each press advances the time in increments of 30 minutes.

The tape counter decreases minute by minute to 0:00, then the VCR
stops recording and turns off automatically.

To extend the duration

Press

REC repeatedly to set a new duration.

To cancel the duration

Press

REC repeatedly until indicator disappears and the VCR returns to

normal recording mode.

To stop while recording

Press

STOP.

Note

• You cannot display the cur rent tape time in the display window when setting the

recording duration.

VIDEO APC

Summary of Contents for SLV-669HF





































































Search results

Summary of Contents for SLV-669HF

Reviews:

Related manuals for SLV-669HF

Brands by name

Popular brands

Sony SLV-669HF, Operating Instructions Manual

Search results

Summary of Contents for SLV-669HF

Reviews:

Related manuals for SLV-669HF

Brands by name

Popular brands