Sony SCD-1/777ES Service Manual Download Page 55

Page: 55 / 78

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

(6)

MAIN SECTION

251

A-4724-951-A MAIN BOARD, COMPLETE

252

1-790-659-11 WIRE (FLAT TYPE) (26 CORE)

253

4-221-249-01 WASHER

254

1-673-854-14 AC BOARD

255

3-701-822-01 HOLDER, WIRE

256

1-771-685-21 SWITCH, PUSH (CONTROL BLOCK) (WIRE)

257

X-4908-910-1 SCREW ASSY (+ BVTT)

258

A-4724-529-A POWER BOARD, COMPLETE

259

4-931-964-01 SCREW (M4X6)

260

A-4724-524-A COAX BOARD, COMPLETE

261

4-913-152-01 ESCUTCHEON, D/O

262

1-673-858-14 OPT BOARD

263

1-673-859-14 SW BOARD

264

A-4724-931-A BAL BOARD, COMPLETE (SCD-1)

265

1-673-855-14 PIN BOARD

266

A-4724-518-A AUDIO BOARD, COMPLETE (SCD-1)

266

A-4724-953-A AUDIO BOARD, COMPLETE (SCD-777ES)

267

4-215-784-11 PANEL, BACK (SCD-1: US, Canadian)

267

4-215-784-21 PANEL, BACK (SCD-1: AEP)

267

4-221-854-01 PANEL, BACK (SCD-777ES: AEP)

267

4-221-854-11 PANEL, BACK (SCD-777ES: US, Canadian)

268

3-701-428-11 SCREW, +B 2.6 CLAW

269

4-221-222-11 BRACKET (FILTER) (SCD-777ES)

269

4-221-222-01 BRACKET (FILTER) (SCD-1)

J150

1-568-918-31 JACK, PIN 1P (LINE OUT (ANALOG) L)

(SCD-777ES)

J150

1-568-918-31 JACK, PIN 1P (LINE OUT (ANALOG)

UNBALANCED L) (SCD-1)

J170

1-563-030-21 CONNECTOR (RECEPTACLE) 3P

(LINE OUT (ANALOG) BALANCED L) (SCD-1)

J250

1-568-918-31 JACK, PIN 1P (LINE OUT (ANALOG)

UNBALANCED R) (SCD-1)

J250

1-568-918-41 JACK, PIN 1P (LINE OUT (ANALOG) R)

(SCD-777ES)

J270

1-563-030-21 CONNECTOR (RECEPTACLE) 3P

(LINE OUT (ANALOG) BALANCED R) (SCD-1)

T401

1-435-108-11 TRANSFORMER, POWER (ANALOG)

(SCD-777ES: AEP)

T401

1-435-110-11 TRANSFORMER, POWER (ANALOG)

(SCD-777ES: US, Canadian)

T401

1-435-114-11 TRANSFORMER, POWER (ANALOG)

(SCD-1: AEP)

T401

1-435-116-11 TRANSFORMER, POWER (ANALOG)

(SCD-1: US, Canadian)

T451

1-435-109-11 TRANSFORMER, POWER (DIGITAL)

(SCD-777ES: AEP)

T451

1-435-111-11 TRANSFORMER, POWER (DIGITAL)

(SCD-777ES: US, Canadian)

T451

1-435-115-11 TRANSFORMER, POWER (DIGITAL)

(SCD-1: AEP)

T451

1-435-117-11 TRANSFORMER, POWER (DIGITAL)

(SCD-1: US, Canadian)

257

256

255

254

253

252

251

255

257

266

257

265

264

259

267

269

US,
Canadian

US, Canadian

SCD-1

SCD-777ES

268

263

262

260

261

258

259

257

#13

not
supplied

#22

#32

BU-23

#22

T401

T451

not supplied

not
supplied

#18

#19

#14

supplied with J170, J270

J170,
J270

#20

J150

J250

#21

not supplied

supplied with J250

supplied with J150

not
supplied

#14

#15

#16

not supplied

267

269

268

#36

#18

#19

#14

J150

J250

#36

#15

#16

#17

The components identified by
mark

or dotted line with

mark

are critical for safety.

Replace only with part num-
ber specified.

Les composants identifiés par une
marque

sont critiques pour la

sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.

Summary of Contents for SCD-1/777ES















































































Search results

Summary of Contents for SCD-1/777ES

Reviews:

Related manuals for SCD-1/777ES

Brands by name

Popular brands

Sony SCD-1/777ES, Service Manual

Search results

Summary of Contents for SCD-1/777ES

Reviews:

Related manuals for SCD-1/777ES

Brands by name

Popular brands