Sony SCD-1/777ES Service Manual Download Page 10

Page: 10 / 78

SECTION 5

TEST MODE

5-1. FLUORESCENT INDICATOR TUBE MODE

Note:

Set the CD1/CD2 switch on the remote commander to CD1.

Procedure:
1. Press the

button while shorting the BP (TEST MODE) on

the DISPLAY board with tweezers, etc. and turn on the power,
so that the following operation will be executed automatically.

(1) All segments from 1G to 19G light up in order, starting from

1G.

(2) Vertical one line (total 7) of all grids from 1G to 15G lights up

in order, starting from the left.

(3) Horizontal one line (total 5) of all grids from 1G to 15G lights

up in order, starting from the top.

(4) Grids from 1G to 15G go off, and all segments from 16G to

19G light up.

2. With the set in the 1-(4) status, pressing any key on the remote

commander changes the display as shown below, and activates
the key check standby mode.

ARTIST

MIN

STEP

INDEX

CD1 CD2 CD3

3. When a key on the front panel is pressed, the corresponding

segment and LED light up. (See table below)

key on set

Key Attribute

Lighting segment (in 19 grids)

Lightning LED

EJECT

20 bit

–

TIME

24 bit

–

TEXT

__|_____ (DIGITAL FILTER)

–

DIGITAL OUT

DIGITAL OUTPUT

–

FILTER

__|_____ (DIGITAL OUTPUT)

–

SACD/CD

NORM

–

PLAY

WIDE

PLAY LED

PAUSE

STD1234

PAUSE LED

STOP

DIGITAL FILTER

–

AMS-BACK

16 bit

CD LED

AMS-FORWARD

OFF

SACD LED

4. If “!%%TEST-END!!%%” is displayed after the keys listed

above were all pressed, the key check terminated successfully.

Note:

As this test does not check the LEDs, check them visually.

5. Press the

button to turn the power off, and disconnect the

plug from the socket.

10G

11G

12G

13G

14G

15G

18G

17G

16G

19G

20G

– DISPLAY Board (Conductor Side) –

CN1002

CN1001

BP (TEST MODE)

Geid Assignment

Summary of Contents for SCD-1/777ES















































































Search results

Summary of Contents for SCD-1/777ES

Reviews:

Related manuals for SCD-1/777ES

Brands by name

Popular brands

Sony SCD-1/777ES, Service Manual

Search results

Summary of Contents for SCD-1/777ES

Reviews:

Related manuals for SCD-1/777ES

Brands by name

Popular brands