SA-WCT100/SS-MCT100
SA-WCT100/SS-MCT100
13
13
2-8. Digital Media Port Test
Note:
SA-WCT100 is connected with SS-MCT100, and remote com-
mander is operation. If SS-MCT100 is not connected, remote
commander cannot be operation.
Procedure:
1. Connect the DMPORT check jig (P/N: J-2501-309-A) with the
DMPORT jack (CN204) on the IO board.
2. Press the [
?/1
] button to turn the power on.
3. Con
fi
rm that both LEDs of the DMPORT check jig lights.
(Con
fi
rmation the power supply line.)
4. Press the [INPUT SELECTOR] button to select the “DMPORT”.
5. Enter the test menu.
6. Press the [] and [VOLUME –] buttons to select
the “DMPORT CHK”, and press the [INPUT SELECTOR]
button.
7. The message “DMPORT OK.” appears on the
fl
uorescent indi-
cator tube and enter the digital media port test mode. (Con
fi
r-
mation of communication line)
When “NO DETECT.” and “UART .TO” are displayed on
the
fl
uorescent indicator tube, con
fi
rm the connection of the
DMPORT check jig, and enter the mode again.
Each time the [
>
] button on the remote commander is
pressed, the connect check and adaptor version check are
changed.
Press the [
.
] button on the remote commander, connected
con
fi
rmation of the DMPORT check jig is done again.
8. To a pinjack of the DMPORT check jig input information rel-
evant to audio signal (sine-wave 1.0V rms).
9. Con
fi
rm the output of speakers. (Con
fi
rmation of analog sig-
nal)
10. To release from this mode, press the [
?/1
] button.
2-9. Cold Reset
Execute this mode when returning the set to the customers.
Procedure:
1. Enter the test menu.
2. Press the [] and [VOLUME –] buttons to select
the “COLD RESET”, and press the [INPUT SELECTOR] but-
ton.
3. The message “COLD RESET.” appears on the
fl
uorescent in-
dicator tube, then turn the power off.
AF
oscillator
DMPORT
check jig
(Part No.:
J-2501-309-A)
J001
SA-WCT100
SS-MCT100
IO board
CN204
MAIN board
CN3008
SECTION 4
TEST MODE
1. TEST MODES OTHER THAN THE TEST MENU
These are executable test mode even if not entering the test menu.
1-1. Cold Reset
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the three buttons [VOLUME –], [INPUT SELECTOR]
and [
?/1
] simultaneously.
3. The message “COLD RESET” appears on the
fl
uorescent indi-
cator tube, then turn the power off.
1-2. HDMI Version Display
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press and hold down the two buttons [VOLUME –] and [IN-
PUT SELECTOR] simultaneously (around 5 seconds).
3. The message “hdmi XX.XX” or “HDMI XX.XX” appears on
the
fl
uorescent indicator tube.
Note:
XX.XX is HDMI microprocessor version.
2. TEST MODES IN THE TEST MENU
These are the test modes done in the test menu.
Setting method of the test menu:
1. Press the [
?/1
] button to turn the power on.
2. Press and hold down the two buttons [] and [IN-
PUT SELECTOR] simultaneously (around 5 seconds).
3. The message “TEST MENU” appears on the
fl
uorescent indi-
cator tube and enter the test menu.
2-1. Panel Test
Procedure:
1. Enter the test menu.
2. Press the [] and [VOLUME –] buttons to select
the “PANEL”, and press the [INPUT SELECTOR] button.
3. All segments in
fl
uorescent indicator tube are lighted up. And
half segments in
fl
uorescent indicator tube are lighted up,
others half segments in
fl
uorescent indicator tube are lighted
up, then all segments in
fl
uorescent indicator tube are lighted
up. Or HDMI indicator LED (amber) is lighted up and down.
These operation is repeated.
4. When all segments in
fl
uorescent indicator tube are lighted up
in the state of step 3, press the [] button and model
information is displayed on the
fl
uorescent indicator tube.
Each time the [] button is pressed, the display
changes from destination information, MC version, SYS ver-
sion, UI version, TA version, DSP version, TM version, CLA
version, CEC version in this order, and returns to the model
information display.
5. In the state of step 3, press the [VOLUME –] button and “K 0”
is displayed on the
fl
uorescent indicator tube.
“K 0” value increases whenever a button on the set is pressed.
However, once a button has been pressed, it is no longer taken
into account.
All buttons on the set is pressed, “OK” and “K 4” are alter-
nately displayed on the
fl
uorescent indicator tube.
6. To release from this mode, press the [
?/1
] button.
2-2. Tone Test
Procedure:
1. Enter the test menu.
2. Press the [] and [VOLUME –] buttons to select
the “TONE TEST”, and press the [INPUT SELECTOR] but-
ton.
3. The message “T. TONE ON” appears on the
fl
uorescent indi-
cator tube and enter the tone test mode.
Then the message “T. TONE FL”, “T. TONE CEN”, “T.
TONE FR”, and “T. TONE SW” is displayed repeatedly. At
the same time, the speaker output is chaged according to the
display.
4. To release from this mode, press the [
?/1
] button.
2-3. AMP Test
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-4. DSP Halt Mode
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-5. VACS On/off
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-6. VACS Display
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-7. DMPORT Device Test
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
