Sony PMW-EX1R Operating Instructions Manual Download Page 136

Page: 136 / 175

Setup Menu List

136

C
o

igur

nd Det

ile
d Set

tings

Country

Setting the area for
use

NTSC Area / PAL Area

Select the color system for the area where you will use the
camcorder.

Note

The default setting is different among the sales areas.

United States and Canada: NTSC Area
Other areas: PAL Area

HD/SD Mode

Switching HD/SD

/ SD

Switch between HD Mode and SD Mode for recording/
playback.
Select “Execute” to switch.

Video Format

Selecting the video
format

HD Mode

Country: NTSC Area

HQ 1920/60i
HQ 1440/60i
SP 1440/60i
HQ 1920/30P
HQ 1440/30P
HQ 1920/24P
HQ 1440/24P
SP 1440/24P
HQ 1280/60P
HQ 1280/30P
HQ 1280/24P

Country: PAL Area

HQ 1920/50i
HQ 1440/50i
SP 1440/50i
HQ 1920/25P
HQ 1440/25P
HQ 1280/50P
HQ 1280/25P

SD Mode

Country: NTSC Area

DVCAM60i SQ
DVCAM60i EC
DVCAM30P SQ
DVCAM30P EC

Country: PAL Area

DVCAM50i SQ
DVCAM50i EC
DVCAM25P SQ
DVCAM25P EC

Select the video format for recording.

HD Mode

• Bit rate

HQ or SP

• Horizontal resolution

1920, 1440, or 1280

• Frame rate

24, 25, 30, 50, or 60

• Scan system

i (interlace) or P (progressive)

SD Mode

• Frame rate

25, 30, 50, or 60

• Scan system

i (interlace) or P (progressive)

• Aspect

SQ (Squeeze) or EC (Edge Crop)

Note

The default setting is different among the sales areas.
United States and Canada: HQ 1920/60i
Other areas: HQ 1920/50i

OTHERS

Menu items

Subitems and setting values

Contents

Summary of Contents for PMW-EX1R
















































































































































































Search results

Summary of Contents for PMW-EX1R

Reviews:

Sony PMW-EX1R, Operating Instructions Manual, Page: 136 / 175

Search results

Summary of Contents for PMW-EX1R

Reviews: