2-6
NEX-EA50CH/EA50CK/EA50EH/EA50H/EA50JH/EA50K/EA50UH
2-1-4. MAIN BOARD SECTION
ns : not supplied
DISASSEMBLY
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
151
1-886-627-11
FP-2015 FLEXIBLE BOARD
152
1-846-004-11
CABLE, FLEXIBLE FLAT (FFC-1002)
153
1-846-003-11
CABLE, FLEXIBLE FLAT (FFC-1001)
154
1-886-622-11
FP-2010 FLEXIBLE BOARD
155
A-1903-481-A AU-1001 BOARD, COMPLETE (Note 2)
156
1-886-628-11
FP-2016 FLEXIBLE BOARD
157
1-886-625-11
FP-2013 FLEXIBLE BOARD
158
A-1903-479-A FP-2001 FLEXIBLE BOARD, COMPLETE
159
A-1903-480-A FP-2000 FLEXIBLE BOARD, COMPLETE
160
4-440-094-01
HOLDER, JS JACK
161
4-440-097-01
FRAME, JS JACK
162
4-440-093-01 CHASSIS,
VC
163
4-440-095-01
FRAME (L), VC
164
4-440-098-01
HEAT SINK, VC
165
4-440-096-01
FRAME (R), VC
166
4-440-100-01 GASKET
(MS)
167
A-1903-478-A MS-1001 BOARD, COMPLETE
168
1-886-637-11
FP-2025 FLEXIBLE BOARD
169
1-886-636-11
FP-2024 FLEXIBLE BOARD
170
4-440-099-01
SHEET, VC RADIATION
171
1-886-626-11
FP-2014 FLEXIBLE BOARD
172
1-886-633-11
FP-2021 FLEXIBLE BOARD
173
4-437-535-01
LABEL (951), FUSE
174
A-1903-969-
B
VC-618 BOARD, COMPLETE (SERVICE) (Note 2)
BH6701 1-251-928-21
SOCKET, BATTERY (Note 1)
BT6701 1-756-134-15
BATTERY, LITHIUM (SECONDARY) (Note 1)
#3
2-660-401-01
SCREW (M1.7), NEW TRU-STAR, P2
#53
3-080-206-21 SCREW,
TAPPING,
P2
Screw
Note
#3
#3
#53
#3
#53
#53
#53
#3
AU-1
001
VC-618
173 174
(Note 2)
172
171
170
151
153
152
158
159
A
B
D
C
E
F
154
156
155
(Note 2)
157
H
H
G
G
160
162
163
161
164
166
169
168
167
165
F
C
E
A
D
B
: BT6701 (LITHIUM BATTERY (SECONDARY))
Board on the mount position.
(See page 6-59)
BT6701
(Note 1)
BH6701
(Note 1)
ns
1. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇
: Solder
#3: M1.7 X 2.5
(Red)
2-660-401-01
2.5
1.7
#53: M2.0 X 5.0 (Tapping)
(Black)
3-080-206-21
5.0
2.0
Note 1:
Replace the battery holder (BH6701) together when replacing
the lithium storage battery (BT6701) on the MS-1001 board.
(The battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first and
attach new lithium storage battery next.
Note 1:
MS-1001
基板のリチウム蓄電池
(BT6701)
を交換する場合は
バッテリホルダ
(BH6701)
も同時に新品に交換してください。
(
一度使用したバッテリホルダは再使用できません。
)
部品取り付けの際は、先にバッテリホルダを取り付けてから
リチウム蓄電池を装着してください。
Caution:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は、正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と交換してく
ださい。
使用済み電池は、取扱指示に従って処分してください。
Note 2:
Refer to "Assembly-7: Routing there Flexible Boards." when
you assemble.
Note 2:
組立て時は
"Assembly-7: Routing there Flexible Boards."
を参
照してください。
The changed portions from
Ver. 1.1 are shown in blue.
