Sony MDS-JE480 Service Manual Download

Page: 29 / 68

MDS-JE480

7. Press the YES button and display “EFB =

MO-W”.

8. Observe the waveform of the oscilloscope, and check that the

specified value is satisfied. Do not rotate the

AMS

knob.
(Write power traverse checking)

(Traverse Waveform)

11. Press the YES button display “EF MO CHECK”

The disc stops rotating automatically.

12. Press the

EJECT button and remove the disc.

13. Load the check disc (MD) TDYS-1.
14. Rotate the

AMS

knob and display “EF CD CHECK”

(C04).

15. Press the YES button and display “EFB =

CD”. Servo is

imposed automatically.

9. Press the YES button display “EFB =

MO-P”.

Then, the optical pick-up moves to the pit area automatically
and servo is imposed.

10. Observe the waveform of the oscilloscope, and check that the

specified value is satisfied. Do not rotate the

AMS

knob.

(Traverse Waveform)

Checking Procedure:
1. Connect an oscilloscope to CN105 pin

(TE) and CN105 pin

(VC) of the BD board.

2. Load a test disc (MDW-74/GA-1). (Refer to Note 1.)
3. Press the

button and move the optical pick-up outside the

pit.

4. Rotate the

AMS

knob and display “EF MO CHECK”.

5. Press the YES button and display “EFB =

MO-R”.

(Laser power READ power/Focus servo ON/tracking servo OFF/
spindle (S) servo ON)

V : 0.5 V/div
H : 10 ms/div
Input : DC mode

Oscilloscope

Specified value : Below 10% offset value

Offset value (%) = X 100

IA – BI

2 (A + B)

Specified value : Below 10% offset value

Offset value (%) = X 100

IA – BI

2 (A + B)

5-6-4. Auto Check

This test mode performs CREC and CPLAY automatically for
mainly checking the characteristics of the optical pick-up. To
perform this test mode, the laser power must first be checked.
Perform Auto Check after the laser power check and Iop compare.

Procedure
1. Press the YES button. If “LDPWR

” is displayed, it

means that the laser power check has not been performed. In
this case, perform the laser power check and Iop compare, and
then repeat from step 1.

2. If a disc is in the mechanical deck, it will be ejected forcibly.

“DISC IN” will be displayed in this case. Load a test disc (MDW-
74/GA-1) which can be recorded.

3. If a disk is loaded at step 2, the check will start automatically.
4. When “XX CHECK” is displayed, the item corresponding to

XX will be performed.
When “06 CHECK” completes, the disc loaded at step 2 will be
ejected. “DISC IN” will be displayed. Load the check disc (MD)
TDYS-1.

5. When the disc is loaded, the check will automatically be resumed

from “07 CHECK”.

6. After completing to test item 12, check OK or NG will be

displayed. If all items are OK, “CHECK ALL OK” will be
displayed. If any item is NG, it will be displayed as “NG:xxxx”.

When “CHECK ALL OK” is displayed, it means that the optical
pick-up is normal. Check the operations of the other spindle motor,
thread motor, etc.
When displayed as “NG:xxxx”, it means that the optical pick-up is
faulty. In this case, replace the optical pick-up.

5-6-5. Other Checks

All the following checks are performed by the Auto Check mode.
They therefore need not be performed in normal operation.

1. Load a continuously recorded test disc (MDW-74/GA-1).

(Refer to “5-5. Using the Continuously Recorded Disc”.)

5-6-6. Traverse Check

Connection :

Specified value : Below 10% offset value

Offset value (%) = X 100

IA – BI

2 (A + B)

6. Observe the waveform of the oscilloscope, and check that the

specified value is satisfied. Do not rotate the AMS knob.
(Read power traverse checking)