Chap
ter
5
B
a
s
ic
F
u
n
c
tion
s
of
Eac
h
Mod
e
5-6 (E)
5-5 Basic Operations in BVE Mode
2
While holding down the MODE button on the control
panel, press L1 (Material) to set the control panel to
material mode.
3
Turn the MULTI CONTROL knob to select the
material, and then press B1 (Load). The selected
material file is loaded to the RP port, and can now be
edited through the editor. The JOG, SHUTTLE and
PLAY operations can also be performed through the
control panel.
x
When performing the operation through the
MAVE-F555
1
Press the port assignment key on the MAVE-F555 to
which the RP port was assigned.
2
Press the “+”/”–” keys on the MAVE-F555.
Notes
• A file in the process of being collected through the R2
port can be loaded to the RP port. However, the RP port
is automatically set to REC INHIBIT, and the file cannot
be saved or edited.
• CTL and TC can be used for the time code reference for
the editor. Note that in order to use TC, set Expansion
Menu “PB TC REPLACE” (menu 642, 643, 644) to
“TM2” in order to output the TM2 data to LTC/VITC.
When a MAVE-F555 is connected for nonlinear editing,
the operation is carried out with TM2 as shown by the
superimposed display. For the above settings, we
recommend you select “TM2.”
Loading a New File for Editing in the RP
Port
x
When performing the operation through the
control panel
1
Press the R1 button or the P1 button to select the RP
port.
2
If a file is loaded in the RP port, hold down the SHIFT
key on the control panel and press B1 (Unload).
3
Hold down the SHIFT key on the control panel and
press B1 (New Material).
4
A BLACK/MUTING file is created and is loaded to
the RP port.
5
The file that is loaded to the RP port can be used for
insert/assemble editing immediately.
x
When performing the operation through the
MAVE-F555
1
Press the R key in the port assignment section of the
MAVE-F555.
2
Press the New File key on the MAVE-F555.
The overall size of the new file can be specified in the setup menu.
For details, refer to Section 3-4, “Setup” (page 3-18).
For details on control panel operation, refer to the BKMA-505
operation manual.
For details on MAVE-F555 operation, refer to the MAVE-F555
operation manual.
Note
The editor’s fast edit function cannot be used to collect a
file through the RP port.
Linear Editing through the RP Port
In order to perform linear editing through the RP port, load
the file to the RP port and then perform insert/assemble
editing through the editor. If the MAV-555SS detects the
end of editing through the editor, an editing results file is
created in the MAV-555SS and is automatically loaded to
the RP port. The output picture momentarily goes to
black.
Notes
• During insert/assemble intervals in RECORDER
material, LTC/VITC are replaced with those of the
PLAYER. In order to consecutively replace the time
codes from the editing results file, set Expansion menu
“PB TC REPLACE” (menu 642, 643, 644) to “TM2” in
order to output the TM2 data to LTC/VITC. When a
MAVE-F555 is connected for nonlinear editing, the
operation is carried out with TM2 as shown by the
superimposed display. For the above settings, we
recommend you select “TM2.”
• The REMOTE setting on the P side is valid. Select the
P1 port first, and then set REMOTE.
Manual Recording through the RP Port
Manual recording through the RP port is possible through
the following procedure:
1
Press the R1 button or the P1 button to select the RP
port.
2
Use the control panel to load a file to the RP port.
3
Cue up the position in the file from which you wish to
begin recording manually.
• You may begin recording from any position within
the file. You cannot, however, specify a recording
start position that is outside of the recorded length
of the file.
