— 29 —
KV-24FS100/25FS100
5-2. PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM INFORMATION
All capacitors are in µF unless otherwise noted. pF : µµF 50WV or less
are not indicated except for electrolytics and tantalums.
All electrolytics are in 50V unless otherwise specifi ed.
All resistors are in ohms. k=1000, M=1000k
Indication of resistance, which does not have one for rating electrical
power, is as follows: Pitch : 5mm Rating electrical power :
1
/
4
W in resistance,
1
/
10
W and
1
/
8
W in chip resistance.
: nonfl ammable resistor.
: fusible resistor.
: internal component.
: panel designation and adjustment for repair.
All variable and adjustable resistors have characteristic curve B, unless
otherwise noted.
Readings are taken with a color-bar signal input.
Readings are taken with a 10M digital multimeter.
Voltages are DC with respect to ground unless otherwise noted.
Voltage variations may be noted due to normal production tolerances.
All voltages are in V.
S : Measurement impossibillity.
: B+line.
: B-line. (Actual measured value may be different).
: signal path. (RF)
Circled numbers are waveform references.
5-1. CIRCUIT BOARDS LOCATION
The
components
identi
Þ
ed
by
shading
and
!
symbol
are
critical
for
safety.
Replace
only
with
part
number
speci
Þ
ed.
The
symbol
indicates
a
fast
operating
fuse
and
is
displayed
on
the
component
side
of
the
board.
Replace
only
with
fuse
of
the
same
rating
as
marked.
Les
composants
identi
Þ
es
per
un
trame
et
une
marque
!
sont
critiques
pour
la
securite.
Ne
les
remplacer
que
par
une
piece
portant
le
numero
speci
Þ
e.
Le
symbole
indique
une
fusible
a
action
rapide.
Doit
etre
remplace
par
une
fusible
de
meme
yaleur,
comme
maque.
The components identifi ed by
X
in this basic schematic diagram have
been carefully factory-selected for each set in order to satisfy regulations
regarding X-ray radiation. Should replacement be necessary, replace
only with the value originally used.
When replacing components identifi ed by
Y
, make the necessary
adjustments as indicated. If the results do not meet the specifi ed value,
change the component identifi ed by
X
and repeat the adjustment until
the specifi ed value is achieved. (Refer to Safety Related Adjustments
on Page 15.)
When replacing the parts listed in the table below, it is important to
perform the related adjustments.
Part Replaced ( )
Adjustment ( )
DY, T585, CRT, IC001, IC561,
C507, C508, C506, T511, L510,
C588, L588, C566, C561, C563,
D567, D568, D566, R567, R568,
R565, R566, R562, R563, R561,
R528....................A Board
HV HOLD-DOWN
R565
REFERENCE INFORMATION
RE
S
I
S
TOR
:
RN
METAL
F
ILM
:
RC
S
OLID
:
F
PRD
NON
F
LAMMABLE
CARBON
:
F
U
S
E
NON
F
LAMMABLE
F
U
S
IBLE
:
RW
NON
F
LAMMABLE
WIREWOUND
:
R
S
NON
F
LAMMABLE
METAL
OXIDE
:
RB
NON
F
LAMMABLE
CEMENT
:
ADJU
S
TMENT
RE
S
I
S
TOR
COIL
:
L
F-
8L
MICRO
INDUCTOR
CAPACITOR
:
TA
TANTALUM
:
P
S S
TYROL
:
PP
POLYPROPYLENE
:
PT
MYLAR
:
MP
S
METALIZED
POLYE
S
TER
:
MPP
METALIZED
POLYPROPYLENE
:
ALB
BIPOLAR
:
ALT
HIGH
TEMPERATURE
:
ALR
HIGH
RIPPLE
SECTION 5: DIAGRAMS
A Board
CV Board
M3 Board