KE-61MR1 (K) 4-16
4-3. CIRCUIT BOARDS LOCATION
4-3-1. DISPLAY UNIT (PDM-6100)
Note:
•
All capacitors are in
µ
F unless otherwise noted. (pF:
µµ
F)
Capacitors without voltage indication are all 50 V.
•
Indication of resistance, which does not have one for rating electrical
power, is as follows.
Pitch: 5 mm
Rating electrical power 1/4 W (CHIP : 1/10 W)
•
All resistors are in ohms.
•
: nonflammable resistor.
•
: fusible resistor.
•
: internal component.
•
: panel designation, and adjustment for repair.
•
All variable and adjustable resistors have characteristic curve B, unless
otherwise noted.
•
: earth-ground.
•
: earth-chassis.
•
#
: not mounted.
•
When replacing the part in below table, be sure to perform the related
adjustment.
•
All voltages are in V.
•
Readings are taken with a 10 M
Ω
digital multimeter.
•
Readings are taken with a color-bar signal input.
•
Voltage variations may be noted due to normal production tolerances.
•
*
: Can not be measured.
•
Circled numbers are waveform references.
•
: B + bus.
•
: B – bus.
•
: Signal path.
4-4. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS
G
D
S
B1 E1
C2
B2 C1
E2
2
3
4
5
6
7
8
9
0
!¡
!™
!¢
!§
!¶
!•
–
1
G
D
S
B2 E2
C1
B1 C2
E1
B2 E2
C1
B1 C2
E1
B2 E2
C1
B1 C2
E1
!ª
B1 E1
E2
C1(B2)
C2
@º
B1
E2
C1
C2
@™
@£
(B2)
E1
(B2)
E1
E2
B1
C2
C1
@¡
B1
E1
C2
B2
C1
E2
G
S
S
D
G
D
B1
E1
C2
B2
C1
E2
B1
E2
C2
C1(B2)
E2
B1
C1
C2
E1(B2)
C2
B1
C1
E2
E1(B2)
C2
B1
C1
E2
B2
E1
C2
Ver.1.6
Transistor
(FET)
Transistor
Transistor
Transistor
Transistor
Transistor
Transistor
Transistor
Transistor
Transistor
Discrete semiconductot
(Chip semiconductors that are not actually used are included.)
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Source
Source
Anode
Anode
(NC)
(NC)
Cathode
Anode
Cathode
Common
Cathode
Cathode
Common
Cathode
Cathode
Common
Common
Common
Common
Cathode
Anode
Base
Emitter
Collector
Base
Emitter
Collector
Drain
Gate
Gate
Drain
Device
Printed symbol
Terminal name
Circuit
Terminal name of semiconductors in silk screen
printed circuit ( )
Anode
Anode
Anode
Cathode
Anode
Anode
Cathode
!£
Transistor
(FET)
Transistor
(FET)
!∞
Emitter
Collector
Base
Transistor
Source
Gate
Drain
Cathode
Anode
Anode
Cathode
Anode
Anode
*
Note: The components identified by shading and
mark
!
are critical for safety. Replace only
with part number specified.
Note: Les composants identifiés par un tramé et
une marque
!
sont critiques pour la
sécurité. Ne les remplacer que par une pièce
portant le numéro spécifié.
TO A1/2, A2/2_1
•
Divided circuit diagram
Schematic diagrams of A, AD, BM1C, DICA, G, M and P boards are divided into serveral pieces.
Information to where the line is to be connected is printed at the end of wach line.
For example, [ TO A1/2, A2/2_1 ] means the line is connected to
Ref. No. 1 of A (1/2) and A (2/2) schematic diagrams.
Circuit diagram division code
Ref. No.
4-3-2. MEDIA RECEIVER UNIT (MBT-MR1)
R1 Board
K3 Board
P Board
R2 Board
G2 Board
G1 Board
F1 Board
K2 Board
U1 Board
IFA Board
M Board
U2 Board
AD Board
AU Board
A Board
H4 Board
H1 Board
H2 Board
H3 Board
MS2 Board
