KE-61MR1 (K) 3-1E
SECTION 3
TROUBLESHOOTING
3-1. DISPLAY UNIT (PDM-6100)
No image
appears.
LED display
Panel module
failure
Blinks alternately.
Blinks six times.
Blinks four times.
G board failure
Temperature sensor
or circuit failure
Just after
start?
YES
NO
Installation
environment?
OK
NG
Fan rotation?
YES
NO
Fan or
circuit failure
Environment
improvement
Blinks.
Just after
start?
YES: Not appear at all.
NO: Appears for a few seconds.
LED display
Lights.
BOX LED
Blinks nine times.
Encrypted authentication
error of box or display
All is normal.
Box LED?
LED display
Lights.
Image erasure
mode
Box failure
Abnormal
Lights.
Priming?
YES: Light emission
NO: No light
emission
P board failure
Check of cable
connection
3-2. MEDIA RECEIVER UNIT (MBT-MR1)
No sound from Both
speakers for all input
Sound not output
from speaker
"MONITOR OUT"
output ?
"SUBWOOFER"
output ?
Display Signal Out
(Black) 26pin output?
26 i
?
YES
YES
YES
YES
NO
(DC signal only)
NO
(try to turn up volume)
(make sure the input signal
is under 200Hz)
•
Check AK4114
(IC5003) on M
•
Check
SN65LVDS1050
(IC5101) on M
•
Check input of
NJW1149
(IC4703) on AU
•
Check AK4524
(IC5002) on M
NO
•
Check CXA2069Qs
(IC4001, IC4303) on AD
Possibility
•
Cable defect
•
Panel failure
No sound from one
speaker for all input
YES
"SURROUND" ON
output?
YES
•
Check CXA2069Q
(IC4001, IC4303) on AD
•
Check input of
NJW1149
(IC4703) on AU
NO
•
Check output of NJW1149
(IC4703) on AU
•
Check output of AK4524
(IC5002) on M
•
Panel failure
NO
NO
Check the source of input signal whichsound does not
come.
•
Check TUNER
•
Check INPUT TERMINAL
•
Check CXA2069Q
(IC4001, IC4303) on AD
Note)
If the condition of small or no sound occurs for only one speaker,
perform the balance adjustment beforehand as follows:
MENU
→
AUDIO
→
BALANCE
→
ADJUST
•
Check of AK4524 (IC5002) on M
No problem when around 3MHz of rectangular wave (3.3Vpp) is output from the 13-pin
SDTO. (The rectangular wave changes depending on the audio signal.)
For the analog system, check the inputs (2 and 3pins) and the outputs (25 through 28pins). The
outputs of these terminals change depending on the volume adjustments.
•
Check of AK4114 (IC5003) on M
No problem when around 3MHz of rectangular wave (3.3Vpp) is output for the JL5003 [SPDIF].
(The rectangular wave changes depending on the audio signal.)
Check that 48kHz of rectangular wave (3.3Vpp) is supplied to the 24-pin LRCK.
•
Check of Display Signal Out (Black) 26pin
The output signal level is about 3.3Vpp when the Display Signal Out terminals are not connected to
the Display unit.
If the signals, SPDIF+/- and /-, are output, no problem for the sending end.
(When the Diplay Signal Out terminals are connected to the Display unit via display interface cable,
the signal level is about 350mVpp since the signal is terminated at Display unit.)
For receiving ends ( SIRCS input and UART input) the check can only be performed when the
Display Signal.
Out terminals are connected to the diplay unit.
(Supply source: AK4524)
Check that 3.072MHz of rectangular wave (3.3Vpp) is supplied to the 26-pin BICK.
(Supply source: AK4524)
