Sony Jumbotron JME-UA200, Service Manual

Page: 14 / 56

1-10 (E)
JME-UA200
18
Adjusting the Luminance Manually
2
Press the ◊ or √ button to select the type of the JumboTron display unit
you are using, then press the ENTER button.
3
Press the ADJUST button.
4
Select MANUAL with the
◊
or
√
button, and press the ENTER button.
The controller enters manual adjustment mode.
5
Select the manual adjustment mode with the ∫ or ı button, or the 0 to
A numberic buttons.
The mode changes in the following order each time you press the ∫
button. (Pressing ı button changes the mode in the reverse order.)
You can also select the mode by pressing the button in brackets. When
you select the mode marked with an asterisk (*), use the buttons in
brackets.
JTU-35
PWM-White [0] PWM-Blue [1] PWM-Red [2] PWM-Green [3] G1-VOLTAGE [4]
*
G1-VOLTAGE (G) [8],
*
G1-VOLTAGE (R) [9],
*
G1-VOLTAGE (B) [A]
PWM-Green (G) [7] PWM-Red (R) [6] PWM-Blue (B) [5]
JTU-17
G1V-White [0] G1V-Blue [1] G1V-Red [2] G1V-Green [3] REF-VOLTAGE [4]
G1V-Green (G) [7] G1V-Red (R) [6] G1V-Blue (B) [5]
* REF-VOLTAGE (B) [8], * REF-VOLTAGE (R) [9], * REF-VOLTAGE (G) [A]
LDU-15
If-White [0] If-Blue [1] If-Red [2] If-Green [3] If-Range [4] If-Blue (B) [5]
If-Green (G) [7] If-Red (R) [6]
* If-Range (B) [8], * If-Range (R) [9], * If-Range (G) [A]
A D J U S T M E N U
M A N U A L
S E N S O R
U N I T T Y P E : J T U - 3 5
Manual adjustment mode
M A N U A L A D J U S T
A D J : P W M - W H I T E
T a r g e t : U N I T
L u m i n a n c e : 0 7 F
B r i g h t n e s s : 0 7
U N I T T Y P E : J T U - 3 5
19
2
Selecting the target of luminance adjustment and setting the unit to the proper
brightness level for carrying out the adjustment
You can adjust the luminance of the whole unit or a specified cell or pixel.
If necessary, you can set the luminance or brightness of the whole unit to
the level at which you can easily make the adjustments. If not necessary to
set, skip steps 8 and 9 below.
6
Press the SETUP button.
7
To change the target of adjustment, select “Target” with the ◊ or √
button, then press the
∫
or
ı
button to change.
The display changes in the order of UNIT, CELL and PIXEL each
time you press the
∫
button. (It changes in the reverse order each time
you press the
ı
button.)
When you select G1-VOLTAGE or REF-VOLTAGE in the procedure
1
, PIXEL does not appear.
Example: Selecting the cell for the target of adjustment
8
To change the luminance or brightness of the whole unit, select
“Luminance” or “Brightness” with the
◊
or
√
button, then change the
data with the ∫ or ı button, or the numeric buttons.
The adjustable range is 256 levels from 000 to 0FF for luminance, and
16 levelss from 00 to 0F for brightness.
The level increases by 1 when you press the
∫ button and decreases by
1 when you press the ı button. You can also select the level by
pressing the numeric buttons that correspond to its level (for exampe,
to set it to 07F, press 0, 7 then F).
Example: Setting the brightness to 0A
Target of adjustment
Luminance
Brightness
A D J U S T S e t U p
A D J : P W M - W H I T E
T a r g e t : U N I T
L u m i n a n c e : 0 7 F
B r i g h t n e s s : 0 7
U N I T T Y P E : J T U - 3 5
A D J U S T S e t U p
A D J : P W M - W H I T E
T a r g e t : C E L L
L u m i n a n c e : 0 7 F
B r i g h t n e s s : 0 7
A D J U S T S e t U p
A D J : P W M - W H I T E
T a r g e t : C E L L
L u m i n a n c e : 0 7 F
B r i g h t n e s s : O A
(Continued)