Sony HT-MT500, Service Manual

Page: 6 / 66

HT-MT500/MT501
6
NETWORK CONNECTION CHECKING METHOD
When the MB-1610 board or WLAN/BT combo card is replaced,
check the connection of wireless/wired LAN.
1. Checking method of wireless LAN connection
Necessary equipment:
• TV monitor
• Access point supporting WPS
Procedure:
1. Connect this unit with TV monitor.
2. Touch the [
1
] button to turn the power on.
3. Press the [HOME] button on the remote commander, display
the home screen.
4. Press the [
V
]/[
v
] buttons on the remote commander to select
the “ Setup”, and press the [ ] button on the remote com-
mander.
5. Press the [
V
]/[
v
] buttons on the remote commander to select
the “Network Settings”, and press the [ ] button on the remote
commander.
6. Press the [
V
]/[
v
] buttons on the remote commander to select
the “Internet Settings”, and press the [ ] button on the remote
commander.
7. Press the [
V
]/[
v
] buttons on the remote commander to select
the “Wireless Setup”, and press the [ ] button on the remote
commander.
8. Press the [
V
]/[
v
] buttons on the remote commander to select
the “Wi-Fi Protected Setup™ (WPS)”, and press the [ ] but-
ton on the remote commander.
9. The message “Start” is displayed.
10. Press the [ ] button on the remote commander, and press the
[WPS] button on the access point.
11. When wireless LAN connection is completed, “Wireless Con-
nection: OK” and “Internet Access: OK” is displayed.
Note: Refer to the Operating Instructions about details of the connection
method.
2. Checking method of wired LAN connection
Necessary equipment:
• TV monitor
• Router
• Network LAN cable
Procedure:
1. Connect this unit with TV monitor.
2. Connect this unit to the router with the network LAN cable.
3. Touch the [
1
] button to turn the power on.
4. Press the [HOME] button on the remote commander, display
the home screen.
5. Press the [
V
]/[
v
] buttons on the remote commander to select
the “ Setup”, and press the [ ] button on the remote com-
mander.
6. Press the [
V
]/[
v
] buttons on the remote commander to select
the “Network Settings”, and press the [ ] button on the remote
commander.
7. Press the [
V
]/[
v
] buttons on the remote commander to select
the “Internet Settings”, and press the [ ] button on the remote
commander.
8. Press the [
V
]/[
v
] buttons on the remote commander to select
the “Wired Setup”, and press the [ ] button on the remote
commander.
5
Adjust the volume.
• Adjust the volume by pressing
Ç
+/– on the remote control.
• Adjust the subwoofer volume by
pressing SW
Ç
+/– on the remote
control (page 26).
• You can play or pause the content
by using the playback operation
buttons on the remote control.
To stop playback by One-touch
function
Touch the N mark on the main unit with
the mobile device again.
• Depending on your device, you may need
to perform the following items on your
mobile device in advance.
– Turn on the NFC function.
– Install the “NFC Easy Connect”
application from Google Play™ and
start the application. (The application
may not be available in some countries/
regions.) For details, refer to the
operating instructions of your device.
• This feature does not work with
BLUETOOTH-compatible headphones. To
listen to sound using a BLUETOOTH-
compatible headphones, see “Listening
to Sound of the Connected TV or Device
from Headphones” (page 30).
• [Bluetooth Mode] is changed to [Receiver]
automatically when making BLUETOOTH
connection with the One-touch function.
Even if the One-touch function is
canceled, the [Bluetooth Mode] setting
remains as [Receiver]. For details about
[Bluetooth Mode], see [Bluetooth
Settings] (page 50).
• If your mobile device is a type that goes
into standby mode in response to
magnetic force, it may not be able to be
connected by NFC. When the One-touch
function does not work, connect it by
using the BLUETOOTH function (page 27).
Notes
.
.
.
.
9. Press the [
V
]/[
v
] buttons on the remote commander to select
the “Auto”, and press the [
b
] button on the remote command-
er.
10. The “The network will be con fi gured with the following set-
tings” screen is display, and press the [
b
] button on the remote
commander.
11. Press the [
V
]/[
v
] buttons on the remote commander to select
the “Save & Connect”, and press the [ ] button on the remote
commander.
12. When wired LAN connection is completed, “Physical Connec-
tion: OK” and “Internet Access: OK” is displayed.
Note:
Refer to the Operating Instructions about details of the connection
method.
NFC CONNECTION CHECKING METHOD
When the MB-1610 board, NFC board or WLAN/BT combo card
is replaced, check the connection of NFC.
By holding an NFC-compatible mobile
device such as a smartphone or tablet
near the N mark on the main unit, the
system is turned on automatically, then
pairing and BLUETOOTH connection are
performed automatically.
Connecting to a Mobile
Device by One-Touch
Function (NFC)
1
Turn on the NFC function of the
mobile device.
2
Touch the N mark on the main unit
with the mobile device.
Keep touching until the mobile
device vibrates and message
appears on the mobile device.
Follow the on-screen instructions to
complete pairing of the main unit
and mobile device.
3
Make sure that the BLUETOOTH
indicator lights in blue.
A connection between the system
and mobile device has been
established.
4
Start audio playback with the
music app on the connected
mobile device.
Sound is output from the system.
Compatible devices
Smartphones, tablets, and music players
with the NFC function built-in
(OS: Android™ 2.3.3 or later, excluding
Android 3.x)
BLUETOOTH indicator
Note:
After checking of NFC connection, refer to “RESETTING THE
SYSTEM” on page 4 and delete the Bluetooth pairing information.