10
z
RET 1 knob
This knob selects from the four return signals from the CCU.
By pressing in the RET 1 button, you can monitor the selected
return video signal in the viewfinder. The signal supplied from
the TEST OUT connector will also be switched.
wj
RET 3 button
By pressing this button, you can view the return video signal
selected by the RET 3 knob in the viewfinder. Pressing this
button again will switch the viewfinder and monitor screen
display back to the camera's video signal.
wk
RET 2 button
By pressing this button, you can view the return video signal
selected by the RET 2 knob in the viewfinder. Pressing this
button again will switch the viewfinder and monitor screen
display back to the camera’s video signal.
wl
RET 1 button
By pressing this button, you can view the return video signal
selected by the RET 1 knob in the viewfinder. Pressing this
button again will switch the viewfinder and monitor screen
display back to the camera’s video signal.
Note
Priority is given in the following order: RET 1, RET 2, RET 3.
When a menu in the RETURN page of the OPERATION menu
is set, pressing the RET 1 and RET 2 buttons will activate RET
3.
e;
ON button
When this button is pressed, the button will light up and the
box cursor will be displayed on the viewfinder screen. When
the button is pressed again, the light will go off and the box
cursor will disappear. This can also be used to switch to the
cross cursor.
ea
STORE (cursor store) button
Press this button to store the size and position of the box
cursor in memory.
Notes
• If the ON button is not lit, box cursor information will not be
stored.
• The cross cursor information cannot be stored.
es
HEIGHT control
Adjust the height of the box cursor displayed on the viewfinder
screen within the effective resolution area.
ed
V-POSI (vertical position) control
Adjust the vertical position of the box cursor displayed on the
viewfinder screen within the effective resolution area.
ef
WIDTH control
Adjust the width of the box cursor displayed on the viewfinder
screen within the effective resolution area.
eg
H-POSI (horizontal position) control
Adjust the horizontal position of the box cursor displayed on
the viewfinder screen within the effective resolution area.
eh
VF (viewfinder) connector (D-sub 25-pin)
Connect to the CAMERA connector on the viewfinder.
Intercom Panel
For JN (USA, Canada, and other countries) models
a
INTERCOM 1 connector (XLR 5-pin)
Connects to an XLR 5-pin headset. The INTERCOM 1
connector can be used for communication via the engineer
line even when the power to the camera has been turned off
from the HDCU2000/2500 Camera Control Unit and the
POWER indicator is lit in red.
b
ENG/PROD (intercom engineer/producer line select)
switch
To switch intercom channel 1 or 2 between producer and
engineer lines.
ENG:
Use the engineer line.
PROD:
Use the producer line.
c
PGM (program audio) 1 control
Adjust the program audio 1 output level.
d
INTERCOM control
Adjust the intercom output level.
e
PGM (program audio) 2 control
Adjust the program audio 2 output level.
f
MIC (microphone) switch
Set the headset microphone to ON/OFF.
PTT:
While the switch is flipped to this position, the headset
microphone is turned on.
ON:
The headset microphone is turned on.
OFF:
The headset microphone is turned off.
g
INTERCOM 2 connector (XLR 5-pin)
Connects to an XLR 5-pin headset.
ENG PROD
INTERCOM
PTT
ON
OFF
PGM1
MIC
INTERCOM 1
INTERCOM 2
PGM2
ENG PROD
INTERCOM
PTT
ON
OFF
PGM1
MIC
PGM2
1
2 3
4
4
5
5
6
6
2 3
7
