![background image](http://html.mh-extra.com/html/sony/hcd-xg100av/hcd-xg100av_service-manual_1329768054.webp)
54
HCD-XG100AV/XG900AV
7-33.
IC PIN FUNCTION DESCRIPTION
•
MAIN BOARD IC501 M30622MAA-A92FP (SYSTEM CONTROLLER (CD MECHANISM CONTROL))
Pin No.
Pin Name
I/O
Description
1
STK-POWER
O
Power amplifier on/off selection signal output “L”: standby mode, “H”: power amplifier on
2
POWER
O
Power on/off control signal output for the audio system (+5V) and deck, panel, audio system
(+7V) and FM/AM tuner unit (+10V) “L”: standby mode, “H”: power on
3
F-RELAY
O
Relay drive signal output for the front speaker protect “H”: relay on
4
REAR-RELAY
O
Relay drive signal output for the rear/center speaker protect “H”: relay on
5
CD-POWER
O
Power on/off control signal output for the CD mechanism deck section
“L”: standby mode, “H”: power on
6
LINE-MUTE
O
Line muting on/off control signal output “L”: muting on, “H”: muting off
7
DBFB-H/L
O
DBFB normal/high selection signal output to the M62493FP (IC101)
“L”: DBFB high, “H”: DBFB low (normal)
8, 9
—
—
Connect to ground
10
XC-IN
I
Sub system clock input terminal (32.768 kHz)
11
XC-OUT
O
Sub system clock output terminal (32.768 kHz)
12
RESET
I
System reset signal input from the reset signal generator (IC801) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
13
X-OUT
O
Main system clock output terminal (16 MHz)
14
VSS
—
Ground terminal
15
X-IN
I
Main system clock input terminal (16 MHz)
16
VDD
—
Power supply terminal (+5V)
17
NMI
I
Non-maskable interrupt input terminal Fixed at “H” in this set
18
WAKE UP
I
Wakeup control signal input from the fluorescent indicator tube driver (IC601) “L” active
19
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2587Q (IC101)
20
RDS-INT
I
Serial data transfer clock signal input from the RDS decoder on the FM/AM tuner unit
(Used for the HCD-XG900AV)
21
RDS-DATA
I
Serial data input from the RDS decoder on the FM/AM tuner unit
(Used for the HCD-XG900AV)
22
AC-CUT
I
AC off detection signal input from the reset signal generator (IC801) “L”: AC cut checked
23
PL-CLK
O
Serial data transfer clock signal output to the M6246FP (IC201)
24
PL-DATA
O
Serial data output to the M6246FP (IC201)
25
PL-LAT
O
Serial data latch pulse output to the M6246FP (IC201)
26
TIMER LED
O
LED drive signal output terminal Not used (open)
27
PROTECT
I
Protect on/off detection signal input from the speaker protect circuit
“L”: protect on, “H”: protect off
28
V MUTE
O
Video muting on/off control signal output to the BA7615N (IC191)
“L”: muting off, “H”: muting on
29
IIC-CLK
I/O
Communication data reading clock signal input or transfer clock signal output with the fluorescent
indicator tube driver (IC601)
30
IIC-DATA
I/O
Communication data bus with the fluorescent indicator tube driver (IC601)
31
NO-USE
O
Not used (open)
32
SQ-DATA
I
Subcode Q data input from the CXD2587Q (IC101)
33
SQ-CLK
O
Subcode Q data reading clock signal output to the CXD2587Q (IC101)
34
SW-MODE
O
Music/movie mode selection signal output to the M62493FP (IC101)
“L”: movie mode , “H”: music mode
35
CD-DATA
O
Serial data output to the CXD2587Q (IC101)
36
H/P IN
I
Connection detection signal input of the headphone jack (J803)
“L”: no connected, “H”: headphone connected
37
CD-CLK
O
Serial data transfer clock signal output to the CXD2587Q (IC101)
38
493-LAT
O
Serial data latch pulse output to the M62493FP (IC101)