31
HCD-M700
m
PLAY MODE/DIRECTION
REC MODE
MD
Z
REPEAT
CLEAR“R”
5-1.
Operating the Continuous Playback Mode
1.
Entering the continuous playback mode
(1) Set the disc in the unit. (Whichever recordable discs or discs for playback only are available)
(2) Press the MD
.
“R” or MD
>
“R” button to display “CPLAY 1MODE” (C34).
(3) Press the ENTER/YES “R”
button to change the display to “CPLAY1MID”.
(4) When access completes, the display changes to “C =
AD =
)”.
Note:
The numbers “ ” displayed show you error rates and ADER.
2.
Changing the parts to be played back
(1) Press the ENTER/YES “R” button during continuous playback to change the display as below.
When pressed another time, the parts to be played back can be moved.
(2) When access completes, the display changes to “C =
AD =
)”.
Note:
The numbers “ ” displayed show you error rates and ADER.
3.
Ending the continuous playback mode
(1) Press the
MENU/NO “R”
button. The display will change to “CPLAY 1MODE” (C34).
(2) Press the
Z
(MD) button and take out the disc.
Note:
The playback start addresses for IN, MID, and OUT are as follows.
IN
: 40h cluster
MID : 300h cluster
OUT : 700h cluster
5-2.
Operating the Continuous Recording Mode (Use only when performing self-recording/playback check)
1.
Entering the continuous recording mode
(1) Set a recordable disc in the unit.
(2) Press the MD
.
“R” or MD
>
“R” button to display “CREC 1MODE” (C35).
(3) Press the ENTER/YES “R” button to change the display to “CREC 1MID”.
(4) When access completes, the display changes to “CREC 1(
)” and “ MD ” lights up.
Note:
The numbers “ ” displayed shows you the recording position addresses.
2.
Changing the parts to be recorded
(1) When the ENTER/YES “R”
button is pressed during continuous recording, the display changes as below.
When pressed another time, the parts to be recorded can be changed. “
MD ” goes off.
(2) When access completes, the display changes to “CREC 1(
)” and “
MD ” lights up.
Note:
The numbers “ ” displayed shows you the recording position addresses.
3.
Ending the continuous recording mode
(1) Press the
MENU/NO “R”
button. The display changes to “CREC 1MODE” (C35) and “ MD ” goes off.
(2) Press the
Z
(MD) button and take out the disc.
Note 1:
The recording start addresses for IN, MID, and OUT are as follows.
IN
: 40h cluster
MID
: 300h cluster
button can be used to stop recording anytime.
Do not perform continuous recording for long periods of time above 5 minutes.
During continuous recording, be careful not to apply vibration.
“CPLAY 1MID”
t
“CPLAY 1OUT”
t
“CPLAY 1IN”
“CREC 1MID”
t
“CREC 1OUT”
t
“CREC 1IN”
Contents
Sets continuous playback when this is pressed in the STOP state. When this is pressed during continu-
ous playback, tracking power servo turns ON/OFF.
Stops continuous playback and continuous recording
The sled moves to the outer circumference only when this is pressed
The sled moves to the inner circumference only when this is pressed
Switches the spindle servo mode (CLV S
y
CLV A)
Switches the pits or grooves each time the button is pressed
Ejects the disc
Releases the test mode
Clears the setting of pits and groove, and judges pits and groove again.
When it is pressed while servo is turning on, the recording starts from present position.
z
MD
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299