![background image](http://html.mh-extra.com/html/sony/hcd-j3md/hcd-j3md_service-manual_420791036.webp)
36
KMS
260A
27X40
B0825
N
Iop = 82.5 mA in this case
Iop (mA) = Digital voltmeter reading (mV)/1 (
Ω
)
(For details of the method for checking
this value, refer to “5-8. Recording and
Displaying IOP Information”.)
Laser power
meter
Optical pick-up
objective lens
Digital voltmeter
BD (MD) board
CN110 pin
5
(I+3V)
CN110 pin
4
(IOP)
V : 0.5 V/div
H : 10 ms/div
Input : DC mode
Oscilloscope
BD (MD) board
CN110 pin
3
(TE)
CN110 pin
1
(VC)
VC
A
B
Specified value : 10% or less of the offset value
Offset value (%) = X 100
I
A – B
I
2 (A + B)
VC
A
B
Specified value : 10% or less of the offset value
Offset value (%) = X 100
I
A – B
I
2 (A + B)
5-6. Checks Prior to Repairs
These checks are performed before replacing parts according to
“approximate specifications” to determine the faulty locations. For
details, refer to “Checks Prior to Parts Replacement and
Adjustments” (See page 14).
5-6-1. Temperature Compensation Offset Check
When performing adjustments, set the internal temperature and room
temperature to 22 to 28°C.
Checking Procedure:
1. Press the
lm
/TUNING – button or
ML
/
button to display “TEMP CHECK”.
2. Press the ENTER/YES “R” button.
3. “T=@@(##) [OK]” should be displayed. If “T=@@ (##) [NG]”
is displayed, it means that the results are bad.
(@@ indicates the current value set, and ## indicates the value
written in the non-volatile memory.)
5-6-2. Laser Power Check
Before checking, check the IOP value of the optical pick-up.
(Refer to “5-8. Recording and Displaying IOP Information”.)
Connection :
Checking Procedure:
1. Set the laser power meter on the objective lens of the optical
pick-up. (When it cannot be set properly, press the
lm
/
TUNING – button or
ML
/ button continuously
to move the optical pick-up.)
Connect the digital volt meter to CN110 pin
5
(I+3V) and
CN110 pin
4
(IOP).
2. Then, press the
lm
/TUNING – button or
ML
/
button and display “LDPWR CHECK”.
3. Press the ENTER/YES “R” button once and display “LD 0.9
mW $
”. Check that the reading of the laser power meter
become 0.84 to 0.92 mW.
4. Press the ENTER/YES “R” button once more and display “LD
7.0 mW $
”. Check that the reading of the laser power meter
and digital volt meter satisfy the specified value.
Specified Value :
Laser power meter reading : 7.0 ± 0.2 mW
Digital voltmeter reading : Optical pick-up displayed value ± 10%
(Optical pick-up label)
Checking Procedure:
1. Connect an oscilloscope to CN110 pin
3
(TE) and CN110 pin
1
(VC) of the BD board.
2. Load a disc (any available on the market). (Refer to Note 1.)
3. Press the
ML
/ button continuously and move
the optical pick-up outside the pit.
4. Press the
lm
/TUNING – button or
ML
/
button and display “EF MO CHECK”.
5. Press the ENTER/YES “R” button and display “EFB =
MO-
R”.
(Laser power READ power/Focus servo ON/tracking servo OFF/
spindle (S) servo ON)
6. Observe the waveform of the oscilloscope, and check that the
specified value is satisfied. Do not press the
lm
/TUNING
– button or
ML
/ button.
(Read power traverse checking)
(Traverse Waveform)
7. Press the ENTER/YES “R” button and display “EFB =
MO-
W”.
8. Observe the waveform of the oscilloscope, and check that the
specified value is satisfied. Do not press the
lm
/TUNING
– button or
ML
/ button.
(Write power traverse checking)
(Traverse Waveform)
5.
Press the MENU/NO “R” button and display “LDPWR
CHECK” and stop the laser emission.
(The MENU/NO “R” button is effective at all times to stop the
laser emission.)
Note 1: After step 4, each time the ENTER/YES “R” button is
pressed, the display will be switched between “LD 0.7 mW
$
”, “LD 6.2 mW $
”, and “LD WP $
”.
Nothing needs to be performed here.
5-6-3. Traverse Check
Connection :
Summary of Contents for HCD-J3MD
Page 20: ...20 ...