![background image](http://html.mh-extra.com/html/sony/hcd-bx6av/hcd-bx6av_service-manual_420587002.webp)
2
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COM-
POSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
SAFETY-RELATED COMPONENT WARNING!!
0
OR DOTTED
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
Wavelength
780 – 790 nm
Frequency response
20 Hz – 20 kHz (±0.5 dB)
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 90 dB
CD OPTICAL DIGITAL OUT
(Square optical connector jack, rear panel)
Wavelength
660 nm
Output Level
–18 dBm
Tape player section
Recording system
4-track 2-channel stereo
Frequency response
40 – 13,000 Hz (±3 dB),
using Sony TYPE I cassette
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range 87.5 – 108.0 MHz
Antenna
FM lead antenna
Antenna terminals
75 ohm unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
US, Canadian models:
530 – 1,710 kHz
(with the interval set at
10 kHz)
531 – 1,710 kHz
(with the interval set at
9 kHz)
AEP, UK and Middle Eastern models:
531 – 1,602 kHz
(with the interval set at
9 kHz)
Other models:
531 – 1,602 kHz
(with the interval set at
9 kHz)
530 – 1,710 kHz
(with the interval set at
10 kHz)
Antenna
AM loop antenna
Antenna terminals
External antenna terminal
Intermediate frequency
450 kHz
General
Power requirements
US, Cnadian models:
120 V AC, 60 Hz
AEP, UK models:
230 V AC, 50/60 Hz
Australian model:
220 – 240 V AC, 50/60 Hz
Mexican model:
120 V AC, 60 Hz
Other models:
110 – 120 V or 220 – 240 V AC, 50/
60 Hz
Adjustable with voltage selector
Power consumption
US model:
160 watts
Canadian model:
180 watts
AEP, UK models:
160 watts
Other models:
160 watts
Dimensions (w/h/d)
Approx. 280 x 325 x 390 mm
Mass
US model:
Approx. 9.2 kg
Canadian model:
Approx. 9.2 kg
AEP, UK models:
Approx. 9.2 kg
Other model:
Approx. 9.1 kg
Supplied accessories:
AM loop antenna (1)
FM lead antenna (1)
Remote Commander (1)
Speaker cords (2)
Center speaker pads (4)
Design and specifications are subject to change
without notice.
This appliance is classified
as a CLASS 1 LASER
product. The CLASS 1
LASER PRODUCT
MARKING is located on
the rear exterior.
TABLE OF CONTENTS
1.
SERVICING NOTES
...............................................
3
2.
GENERAL
Location of Controls .......................................................
4
Setting the Time ..............................................................
5
3.
DISASSEMBLY
.........................................................
6
4.
DIAGRAMS
4-1. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 11
4-2. Schematic Diagram – CD Section (1/4) – ..................... 12
4-3. Schematic Diagram – CD Section (2/4) – ..................... 13
4-4. Schematic Diagram – CD Section (3/4) – ..................... 14
4-5. Schematic Diagram – CD Section (4/4) – ..................... 15
4-6. Printed Wiring Boards – CD Section – ......................... 16
4-7. Printed Wiring Boards – MAIN Section – .................... 17
4-8. Schematic Diagram – MAIN Section (1/4) – ................ 18
4-9. Schematic Diagram – MAIN Section (2/4) – ................ 19
4-10. Schematic Diagram – MAIN Section (3/4) – ................ 20
4-11. Schematic Diagram – MAIN Section (4/4) – ................ 21
4-12. Printed Wiring Boards – PANEL Section – .................. 22
4-13. Schematic Diagram – PANEL Section – ....................... 23
4-14. Printed Wiring Boards
– AMP/POWER SUPPLY Section – ............................. 24
4-15. Schematic Diagram – FRONT AMP Section – ............ 25
4-16. Schematic Diagram
– CENTER/REAR AMP Section – ................................. 26
4-17. Schematic Diagram – POWER SUPPLY Section – ...... 27
5.
EXPLODED VIEWS
................................................ 33
6.
ELECTRICAL PARTS LIST
............................... 39
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299