5-37
8. Burst Cleaning Adjustment for PAL model
(CB-61 board)
Adjust to the optimum PAL chroma signal demodulation phase. If
the phase is not correct, moire distortion noises will stand out.
Mode
VTR stop
Signal
Color bar
Measurement Point
Pin
2
of CN9925 (VG)
Measuring Instrument
Oscilloscope
Adjustment Page
D
Adjustment Address
60
Specified Value
A = 0 ± 50mV
Note:
Perform “8. Burst Cleaning Adjustment for PAL model” and “9.
Color Adjustment for PAL model” alternately until each specified
value is satisfied.
Adjusting method:
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: D, address: 60, change the data and set the flicker
amplitude(A) of the cyan or green section to minimum.
3)
Press the PAUSE button of the adjustment remote commander.
4)
Select page: 0, address: 01, and set data: 00.
5)
Perform “Color Adjustment for PAL model”.
Fig. 5-3-31.
9. Color Adjustment for PAL model (CB-61 board)
Set the color saturation to the standard value. If deviated, the color
will be to dark or light.
Mode
VTR stop
Signal
Color bar
Measurement Point
Pin
2
of CN9925 (VG)
Measuring Instrument
Oscilloscope
Adjustment Page
D
Adjustment Address
6D
Specified Value
A = 0.54 ± 0.05V
Adjusting method:
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: D, address: 6D, change the data and set the voltage
(A) between the yellow and green to the specified value.
3)
Press the PAUSE button of the adjustment remote commander.
4)
Select page: 0, address: 01, and set data: 00.
5)
Check that the specified value of “Burst Cleaning Adjustment”
is satisfied, if not perform “Burst Cleaning Adjustment”.
Fig. 5-3-32.
Cyan
A
2H
Green
Yellow
A
2H
Summary of Contents for GV-D300 Operating Instructions (primary manual)
