Sony FilmStation UP-DF550 Manual Download Page 17 | Manualshive

Page: 17 / 58

background image

Pre

par

at

ion

Connections

17

Notes

• Be sure to use casters and stopper sheet (sold

separately) when placing the unit vertically.
Otherwise, the unit may topple and cause injury.

• When pulling the unit in and out while the unit is

equipped with the casters, be careful not to damage the
power cord, LAN cable, and so on.

• When placing the unit vertically, make sure the LCD

is near the floor, and leave a space of more than 8 cm
(3 1/4 inches) between the top of the unit and the
anything located above it to prevent blocking the
ventilation holes.

Connections

Connect the unit to a 100BASE-TX LAN.

Notes

• Connect the AC power cord last.
• Before connecting to the LAN, be sure to set up the

required IP address and sub-net mask.
For detailed information, consult the system
administrator.

Notes on the 100BASE-TX cable

• Be sure to use a network cable of less than 30 m (98

feet 5 1/4 inches) in length, and rated more than
category 5.

• It is recommended that you use a shielded cable.

Turning the Unit On or Off

Turn the printer power on after you connect the AC
power cord.

Secure the front caster using the stopper sheet

(sold separately).
Be sure to place the roller of the caster in the groove
of the stopper sheet.

Secure the unit using the front caster
(sold separately).

Stopper sheet
(sold separately)

Stopper sheet
(sold
separately)

100BASE-TX
cable

to the LAN

Power cord

to

-

AC IN

to the

network connector

«
...
15
16
17
18
19
...
»

Summary of Contents for FilmStation UP-DF550



























































Reviews:

No comments

Related manuals for FilmStation UP-DF550

Brand: Labnet Pages: 5

Brand: Tabi Pages: 8

Brand: Dabi Atlante Pages: 102

Brand: Gatekeeper Pages: 8

Bure Rise & Go DB 56-309

Brand: Gate Pages: 8

Brand: Tascam Pages: 8

Brand: K-LASER Pages: 70

Brand: K-LASER Pages: 72

Cell Saver Elite+

Brand: Haemonetics Pages: 230

Brand: MÄDLER Pages: 4

Brand: Interacoustics Pages: 25

500 FleetBroadband

Brand: Sailor Pages: 20

Brand: Max Tapener Pages: 2

Brand: Master Pages: 80

Brand: Steren Pages: 2

Brand: Southwire Pages: 15

Brand: Ambu Pages: 32

Brand: Reichert Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands