Sony DWTB01/E1424 Operating Instructions Manual Download Page 28

Page: 28 / 32

Specifications

microphone cable, moving the microphone
connection away from the antenna, or
lowering the transmission power.

Specifications

Transmitting section

Oscillator type

Crystal-controlled PLL synthesizer

RF power output

1 mW/10 mW/50 mW (e.r.p)

selectable

Antenna type

/4 flexible wire

Occupied RF bandwidth

192 kHz or less

Audio delay

1.5 ms

Allowable deviation of transmission

frequency

±6.5 ppm

Type of emission

G1E or G1D

Modulation method

/4 Shift QPSK

Audio section

Maximum input level

MIC: –22 dBu (with 0 dB

attenuator)

LINE: +24 dBu

Audio attenuator adjustment range (pad)

0 to 48 dB (3dB steps, MIC input

mode only)

Microphone input connector

Sony 4-pin (SMC9-4S) (female)

Input impedance

4.7 kohms or more

Frequency response

20 Hz to 22,000 Hz

T.H.D 0.03% or less
Dynamic range

106 dB or more

0 dBu = 0.775 V

To prevent electromagnetic
interference from portable
communication devices

The use of portable telephones and
other communication devices near
the DWT-B01 may result in
malfunction and interference with
audio signals. It is recommended that
portable communication devices near
the DWT-B01 be turned off.

Summary of Contents for DWTB01/E1424

































Search results

Summary of Contents for DWTB01/E1424

Reviews:

Related manuals for DWTB01/E1424

Brands by name

Popular brands

Sony DWTB01/E1424, Operating Instructions Manual

Search results

Summary of Contents for DWTB01/E1424

Reviews:

Related manuals for DWTB01/E1424

Brands by name

Popular brands