DSX-GS900
6
Sony CONFIDENTIAL
For Authorized Servicer
DESTINATION SETTING METHOD
After replacing the MAIN board, perform the following procedure,
only when con
fi
rm the destination code and the correct destination
code is not displayed.
Note 1:
This work is unnecessary if “CONFIRMATION OF DESTINA-
TION SETTING CODE” on page 5 is performed and the correct
destination code is displayed.
Setting procedure:
1. Press and hold the [ OFF SRC] button to the state of source off
(the clock is displayed on the liquid crystal display), enter the
test mode by pressing the buttons in order of the [ 4]
→
[MIC
5]
→
[
u
6] (press only the [
u
6] button for 2 seconds) and
display the software main version.
(Displayed characters/values in the following
fi
gure are exam-
ple)
[ 4]
press
[MIC 5]
press
Software main version
[
u
6]
press for
2 seconds
2. In the state in which the software main version is displayed on
the liquid crystal display, enter the destination setting mode by
pressing the buttons in order of the [
>
M
]
→
[
m
.
]
→
[PUSH ENTER/MENU/ VOICE].
(Displayed characters/values in the following
fi
gure are exam-
ple)
[
m
.
] press
[
>
M
] press
Destination code
(“XXXXXX” is displayed
with alphanumeric
characters)
OP0
OP1
OP2
OP3
OP4
OP5
6 digits
XXXXXX
[PUSH ENTER/MENU/
VOICE] press
3. Input the 6 digits destination code (728332).
Rotate the control dial to select “7” with the OP5 digit and press
the [PUSH ENTER/MENU/ VOICE] or [
>
M
] button.
Rotate the control dial to select “2” with the OP4 digit and press
the [PUSH ENTER/MENU/ VOICE] or [
>
M
] button.
Rotate the control dial to select “8” with the OP3 digit and press
the [PUSH ENTER/MENU/ VOICE] or [
>
M
] button.
Rotate the control dial to select “3” with the OP2 digit and press
the [PUSH ENTER/MENU/ VOICE] or [
>
M
] button.
Rotate the control dial to select “3” with the OP1 digit and press
the [PUSH ENTER/MENU/ VOICE] or [
>
M
] button.
Rotate the control dial to select “2” with the OP0 digit.
Note 2:
The digit return by pressing the [MODE ] or [
m .
] button.
Contorol dial rotate to
select the alphanumeric
characters.
[
m
.
] press
to return the digit.
[
>
M
] press
to advance the digit.
[MODE ] press
to return the digit.
Destination code
[PUSH ENTER/MENU/
VOICE] press to
advance the digit.
XXXXXX
OP0
OP1
OP2
OP3
OP4
OP5
6 digits
Note 3:
Destination code input can also be done with the remote command-
er supplied with this unit.
Instead of rotating the control dial, press the [
V
] or [
v
] button.
To advance the digit for press the [
b
] or [ENTER] button, to return
the digit for press the [
B
] button.
[
b
] press to
advance the digit.
[
B
] press to return
the digit.
[
V
] press to select
the alphanumeric
characters.
[
v
] press to select
the alphanumeric
characters.
[ENTER] press to
advance the digit.
– Continued on next page –
SYS SET
2019/10/17 22:00:30 (GMT+09:00)
