6-44
Initializing Method:
1) Set data: 01 to page: 1, address: 00.
2) Set data: 01 to page: 4, address: 02, and press the PAUSE button
of the adjusting remote commander.
3) Check that the data of page: 4, address: 02 changes in the order
of “01”, “03”, “05”, “00”.
4) Set data: FF to page: C, address: 01, and press the PAUSE button
of the adjusting remote commander.
5) Set data: 03 to page: C, address: 62, and press the PAUSE button
of the adjusting remote commander.
6) Change the data only for the PAL mode.
Press the PAUSE button of the adjusting remote commander
each time when setting new data to write the data in the non-
volatile memory.
7F
F4
7E
Data
Address
08
13
19
7) Set data: 00 to page: 1, address: 00.
3. Initializing the Page C Data
Note:
If the page C data is initialized, the following adjustments
must be performed again.
All RF block adjustments of “Video System Adjustments”
and “Servo System Adjustments”.
3-3. SYSTEM CONTROLLER SYSTEM ADJUSTMENTS
1. Initializing the Page D Data
Note:
If the page D data is initialized, the following adjustments
must be performed again.
“LCD System Adjustments”, “Color Electronic View finder
System Adjustments”, “ID Board Threshold Level
Adjustment”, “Battery Down Adjustment”, and “Base Band
Block Adjustment” and “Clock Adjustment” of the “Video
System Adjustment”.
Adjustment Page
Adjustment Address
C
00 to 6F
Adjustment Page
Adjustment Address
D
10 to 69, C8 to FF
Initializing Method:
1) Set data: 01 to page: 1, address: 00.
2) Set data: 2D to page: 2, address: 00, and press the PAUSE button
of the adjusting remote commander.
3) Set data: 2D to page: 2, address: 01, and press the PAUSE button
of the adjusting remote commander.
4) Check that the data of page: 2, address: 02 is “01”.
5) Perform “Changing the Page D Data”.
2. Changing the Page D Data
If the page D data has been initialized, change the data as shown in
the following table by manual input.
Note 1:
Before changing the data, set data: 01 to page: 1, address:
00.
Note 2:
When changing the data, press the PAUSE button of the
adjusting remote commander each time when setting new
data, since the data is written in the non-volatile memory.
Note 3:
After changing the data, set data: 00 to page: 1, address:
00.
Data
12
13
14
1C
1E
23
28
2A
2B
2C
2D
2E
2F
4C
4D
66
68
E4
F8
F9
FA
FD
02
46
0C
02
C0
08
10
04
44
11
0C
02
0B
0D
5A
26
35
4E
80
C0
08
0A
61
87
1C
D9
79
09
NTSC
PAL
Address
Summary of Contents for DCR-PC7
