Remote Control
Location of controls
To turn on/off the power
Press POWER.
To adjust the volume
Press , – (VOL +, – on the remote).
To listen through headphones
Connect the headphones to the
i
(headphones) jack.
Adjusting the sound emphasis
To reinforce the bass sound
Press MEGA BASS.
“MEGA BASS” appears in the display.
To return to normal sound, press the button again.
To get the MEGA Xpand effect
Press MEGA Xpand.
"MEGA Xpand" appears in the display.
You can get the effect of expansion of the sound field.
To return to normal sound, press the button again.
Falling asleep to music
1
Play the music source you want.
2
Press SLEEP to display “SLEEP.”
3
Press SLEEP to select the minutes until the player goes off automatically.
Each time you press the button, the indication changes as follows: “60”
t
“90”
t
“120”
t
"OFF"
t
“10”
t
“20”
t
“30”.
To cancel the sleep function
Press POWER to turn off the power.
Note
When you are playing a tape using this function:
If the tape length of one side is longer than the set time, the player will not go off until the tape reaches
the end.
SLEEP
FUNCTION
Number buttons
MODE
TUNE +,–
BAND
MEGA
Xpand
N
POWER
VOL +*, –
x
X
.
,
>
MEGA
BASS
Total track number
Programmed track
Playing order
D
E
Total playing time
Display
MEGA BASS
Z
PUSH OPEN/CLOSE
*, –
DSPL/ENT/MEM
MODE
i
x
POWER
SLEEP
OPR/BATT
Loading a CD
With the labeled side up
Inserting a cassette
CD
RADIO BAND•AUTO PRESET
TAPE
MEGA Xpand
Display
Remote sensor
Listening to the radio
1
Press RADIO BAND•AUTO PRESET until the band you want appears in the
display (direct power-on).
Each time you press the button, the indication changes as follows:
“FM”
t
“AM”.
2
Hold down TUNE + or – until the frequency digits begin to change in the
display.
The player automatically scans the radio frequencies and stops when it finds a
clear station.
If you can't tune in a station, press the button repeatedly to change the frequency
step by step.
Tip
If the FM broadcast is noisy, press MODE repeatedly until "Mono" appears in the display and the radio
will play in monaural.
Presetting radio stations
You can store radio stations into the player’s memory. You can preset up to 30 radio stations , 20
for FM and 10 for AM in any order.
1
Press RADIO BAND•AUTO PRESET to select the band.
2
Hold down RADIO BAND•AUTO PRESET for 2 seconds until “AUTO” flashes
in the display.
3
Press DSPL/ENT/MEM.
The stations are stored in memory from the lower frequencies to the higher ones.
If a station cannot be preset automatically
You need to preset a station with a weak signal manually.
1
Press RADIO BAND•AUTO PRESET to select the band.
2
Tune in a station you want.
3
Hold down DSPL/ENT/MEM for 2 seconds until the preset number flashes in the display.
4
Press or – until the preset number you want for the station flashes in the display.
5
Press DSPL/ENT/MEM.
The new station replaces the old one.
On the remote
1
Press BAND until the band you want appears in the display.
2
Tune in a station you want.
3
Hold down the number buttons that you want to preset the new station on for about 2 seconds.
To select the preset number over 10, press >10 first, then the corresponding number buttons.
You need to hold down the last number button to enter for about 2 seconds.
(Example: To select 12, press >10 and 1 first, then hold down 2 for about 2 seconds.)
Tip
The preset radio stations remain in memory even if you unplug the AC power cord or remove the
batteries.
Playing preset radio stations
1
Press RADIO BAND•AUTO PRESET to select the band.
2
Press or – to tune in the stored station.
On the remote
1
Press BAND.
2
Press the number buttons to tune in the stored station.
To tune in a preset station over 10, press >10 first, then corresponding number buttons.
(Example: To tune in a preset station 12, press >10 and 1 first, and then press 2.)
Playing a tape
1
Press TAPE (direct power-on).
(On the remote, press POWER and then press FUNCTION repeatedly until
"TAPE" appears in the display.)
2
Press
xZ
to open the tape compartment and insert a recorded tape. Close the
compartment. Use TYPE I (normal) tape only.
3
Press
N
.
To
stop playback
fast-forward or rewind the tape
pause playback
eject the cassette
Recording
1
Press
xZ
to open the tape compartment and insert a blank tape. Use TYPE I
(normal) tape only.
2
Select the program source you want to record.
To record from the CD player
Press CD and insert a CD (See “Playing a CD”).
To record from the radio
Press RADIO BAND•AUTO PRESET and tune in the station you want (See
“Listening to the radio”).
3
Press
z
to start recording.
(
N
is depressed automatically.)
To
Press
stop recording
xZ
pause recording
X
Press the button again to resume recording.
Tips
• Adjusting the volume or the audio emphasis will not affect the recording level.
• For the best results, use the AC power as a power source for recording.
• To erase a recording, proceed as follows:
1 Insert a tape with the recording you want to erase.
2 Press TAPE.
3 Press
z
.
Press
xZ
M
or
m
X
Press the button again to resume play after pause.
xZ
Then do this
Press
.
or
>
to select the track that you
want to repeat, then press
u
.
Press
u
.
Press
u
.
Press
u
.
Press
.
or
>
then press DSPL/ENT/MEM
for the tracks you want to program in the order
you want up to 20 tracks (see fig.
E
). Then press
u
.
Press
.
or
>
then press DSPL/ENT/MEM
for the tracks you want to program in the order
you want up to 20 tracks. Then Press
u
.
TUNE –, +
m
,
M
PRESET –, +
.
,
>
u
*
With the side you want
to play facing upward
*
*The button has a tactile dot.
Playing a CD
1
Press CD (direct power-on).
(On the remote, press POWER and then press FUNCTION repeatedly until
"Cd" appears in the display.)
2
Load a CD in the CD compartment.
3
Press
Z
PUSH OPEN/CLOSE to close the CD compartment.
4
Press
u
(
N
on the remote).
The player plays all the tracks once.
To
stop playback
pause playback
go to the next track
go back to the previous track
remove the CD
locate a point while listening
to the sound
locate a point while observing
the display
locate a specific track directly*
* You cannot locate a specific track if "SHUF" or "PGM" is lit in the display. Turn off the indication by
pressing
x
.
Tip
To locate a track numbered over 10, press >10 first, then the corresponding number buttons on the
remote.
Example:To play track number 23, press >10 first, then 2 and 3.
Using the display
To check the total track number and playing time
Press DSPL/ENT/MEM in stop mode (see fig.
D
).
To check the remaining time
Press DSPL/ENT/MEM repeatedly while playing a CD. The display changes as follows:
t
the current track number and playing time
r
the current track number and the remaining time on the current track*
r
the number of tracks left and remaining time on the CD
* For a track whose number is more than 20, the remaining time appears as “- -:- -” in the display.
Selecting the play mode
Press MODE until “REP 1” “REP ALL” “SHUF” “SHUF REP” “PGM” “PGM REP” appears in
the display. Then proceed as follows:
To
Select
repeat a single track
“REP 1”
repeat all the track
“REP ALL”
shuffle play
“SHUF”
repeat tracks
“SHUF REP”
in random order
program play
“PGM”
repeat programmed tracks
“PGM REP”
On the remote
When you’ve selected “PGM” or “PGM REP”, press the number buttons for the track you want
up to 20 tracks, then press
N
.
To cancel selected play mode
Press MODE repeatedly until the selected mode disappears from the display.
To check the programmed track and playing order in the display
To check the order of tracks before play, press DSPL/ENT/MEM.
Every time you press the button, the track number appears in the programmed order.
To change the current program
Press
x
once if the CD is stopped and twice if the CD is playing. The current program will be
erased. Then create a new program following the programming procedure.
Tips
• You can play the same program again, since the program is saved until you open the CD
compartment.
• You can record your own program. After you’ve created the program, insert a blank tape and press
z
to start recording.
Press
x
u
(
X
on the remote)
Press the button again to resume play after pause.
>
.
Z
PUSH OPEN/CLOSE
M
(forward) or
m
(backward) while playing until you
find the point (
>
or
.
on the remote)
M
(forward) or
m
(backward) in pause until you find
the point (
>
or
.
on the remote)
a number button of the track on the remote
