Sony Bravia KDL-43WG6 Series Page 60 Service Manual Download

Page: 60 / 151

6.4.2 USB Port 2

– No Detection / Cannot Play / No picture / No Sound – General Checking

6.4.2 USB Port 2

TV turn ON condition:

START

*1 Confirm USB Auto

Start is ON or OFF

Check 5V at

C7017 (USB

port2)

*2 Confirm USB

file format

Change to supported USB format

Change to ON

Change B-Board

Main IC (IC5000) problem

OFF

END

No 5V

USB format OK but No detection

Do a Factory Setting

Have 5V but No detection

Detection OK

Picture OK

Sound OK

Detection OK

and

Picture and Sound OK

Audio IC IC3500) problem

Picture NG

Sound NG

Remarks:

*2 Confirm with OSD on bottom panel, if
playback not support.
Please refer to IM for detail supported USB
format.

*1 Confirm USB Auto Start at Set-up Menu.

SYS SET

2019/01/30 02:46:26 (GMT+09:00)

Summary of Contents for Bravia KDL-43WG6 Series
























































































































































Search results

Summary of Contents for Bravia KDL-43WG6 Series

Reviews:

Related manuals for Bravia KDL-43WG6 Series

Brands by name

Popular brands

Sony Bravia KDL-43WG6 Series, Service Manual

Search results

Summary of Contents for Bravia KDL-43WG6 Series

Reviews:

Related manuals for Bravia KDL-43WG6 Series

Brands by name

Popular brands