7. ATAPI Packet Command Specification
REQUEST SENSE
SONY AIT-2 Turbo drive SDX-560V series Ver.1.0
7-58
ILLEGAL REQUEST
. Indicates that there was an illegal parameter in the Command
Descriptor Block or in the additional parameters supplied as data for some commands. If
the target detects an invalid parameter in the command descriptor block, then it shall
terminate the command without altering the medium. If the target detects an invalid
parameter in the additional parameters supplied as data, then the target may have already
altered the medium. This sense key may also indicate that an invalid IDENTIFY message
was received.
1A 00
PARAMETER LIST LENGTH ERROR-Indicates that the Parameter Length error in the
Command Descriptor Block. Either the value does not fall on a Header, Page or Block
descriptor boundary or the Parameter List Length is unexpectedly large.
20 00
INVALID COMMAND OPERATION CODE-Invalid or Unsupported command.
24 00
INVALID FIELD IN CDB - Bits are set in one or more fields are not supported or are
Reserved. Refer to the Field Pointer (Bytes 15-17) to identify the illegal bit or field.
25 00
LOGICAL UNIT NOT SUPPORTED-The error indicates that the LUNTRN field
in the Identify message was not ZERO.
26 00
INVALID FIELD IN PARAMETER LIST-Test Number,
Configuration Number Header, or Field in the Parameter List was invalid or selected
Diagnostic test is not Host assessable.
26 01
PARAMETER NOT SUPPORTED-Unsupported page requested. Refer to the Field
Pointer (Bytes 15-17) to identify the illegal bit or field.
26 02
PARAMETER VALUE INVALID
2C 00
2C 00 COMMAND SEQUENCE ERROR - Write Buffer command when tape is inserted and not at BOT.
39 00
SAVING PARAMETERS NOT SUPPORTED
3D 00
INVALID BITS IN IDENTIFY MESSAGE-Identify message was not 80h or C0h.
55 04
INSUFFICIENT REGISTRATION RESOURCES
83 02
No MIC Detected
83 04
MIC out of Memory
83 05
No Data Body Detected in the MIC
83 0C
MIC format type is undefined
83 0D
MIC capacity field indicates illegal value.
83 80
Partition Count exceeded
83 89
User Volume Note Size Mismatch
83 8A
User Partition Note Size Mismatch
83 97
Current Partition is not the last partition
83 98
Can not append the new partition, because remaining capacity too short.
83 99
Can not delete partition
83 9B
Can not format tape because real tape capacity is exceeded
05h
83 9C
Can not append new partitions because the MIC is out of memory
UNIT ATTENTION
. Indicates that the removable medium may have been changed or
the target has been reset.
28 00
NOT READY TO READY TRANSITION, MEDIUM MAY HAVE CHANGED
29 00
POWER ON, RESET, OR BUS DEVICE RESET OCCURRED
29 80
Drive Failed Power-on test or Diagnostic-(SONY Unique)
2A 01
MODE PARAMETERS CHANGED-Issued to the host after the host
changes any Mode Parameter.
06h
83 87
Broken MIC is loaded in AIT mode
DATA PROTECT
. Indicates that a WRITE type of operation was attempted on a write
protected tape, write operation is not performed.
27 00
WRITE PROTECTED-Cassette is Write Protected.
07h
83 0B
83 0B BROKEN MIC–Cassette is Write Protected
BLANK CHECK
. Indicates the drive encountered blank medium or end-of-data
indication while reading.
00 00
NO ADDITIONAL SENSE INFORMATION-Blank Tape was encountered at BOT
08h
00 05
END-OF-DATA DETECTED-During READ or SPACE command.
Vendor
Specific
83 08
MIC is not formatted yet
83 0B
MIC is broken
09h
83 83
MIC is exist but is not used
ABORTED
COMMAND
48 00
HOST DETECTED ERROR MESSAGE RECEIVED.
4A 00
COMMAND PHASE ERROR
4B 00
DATA PHASE ERROR - Possible DMA error
0Bh
4E 00
OVERLAPPED COMMANDS ATTEMPTED-Host issued a new command to the drive
while a previous command was being executed.
VOLUME
OVERFLOW
0Dh
00 02
END-OF-PARTITION/MEDIUM DETECTED-During Write type operation.
0Eh
MISCOMPARE.
Not
supported
0Fh
Reserved
