background image

AR-B1474 User

¡¦

s Guide

3-3

3.2.2  Hard Disk (IDE) Connector (CN1)

A 40-pin header type connector (CN1) is provided to interface with up to two embedded hard disk drives (IDE AT
bus).  This interface, through a 40-pin cable, allows the user to connect up to two drives in a “daisy chain” fashion.
To enable or disable the hard disk controller, please use BIOS Setup program to select.  The following table
illustrates the pin assignments of the hard disk drive’ s 40-pin connector.

1

2

39

40

Figure 3-5 CN1: Hard Disk (IDE) connector

Pin

Signal

Pin

Signal

1

-RESET

2

GROUND

3

DATA 7

4

DATA 8

5

DATA 6

6

DATA 9

7

DATA 5

8

DATA 10

9

DATA 4

10

DATA 11

11

DATA 3

12

DATA 12

13

DATA 2

14

DATA 13

15

DATA 1

16

DATA 14

17

DATA 0

18

DATA 15

19

GROUND

20

Not used

21

Not Used

22

GROUND

23

-IOW

24

GROUND

25

-IOR

26

GROUND

27

Not Used

28

BALE

29

Not Used

30

GROUND

31

IRQ14

32

-IOCS16

33

SA 1

34

Not used

35

SA 0

36

SA 2

37

-CS 0

38

-CS 1

39

HD LED A

40

GROUND

      Table 3-1 HDD Pin Assignment

3.2.3  Power Connector (J5)

J5 is 8-pin power connector. Using the J5, you can connect the power supply to the on board power connector for
stand alone applications directly.

1  GND

2  +5VDC

3  +5VDC

4  GND

5  GND

6  +12VDC

7  -12VDC

8  -5VDC

J5

Figure 3-6 J5: Power Connector

Summary of Contents for 486DX








































































Reviews: