Sony Ericsson K610i Working Instructions Download Page 5

Page: 5 / 53

Working Instruction

Mechanical

3/000 21-1/FEA 209 544/109 B

Sony Ericsson Mobile Communications AB

5(53)

1.2 General cautions

The following cautions are considered to be generic for all phone models and will not be repeated in
the Disassembly, Replacements and Reassembly sections:

•

KEEP ALL CONTACT SURFACES CLEAN

•

BE CAREFUL WHEN USING TOOLS LIKE THE DENTIST HOOK

TWEEZERS

OPENING TOOLS

GUITAR PICK

ETC

TO AVOID SCRATCHES OR DAMAGES TO THE EXTERIOR AND INTERIOR PARTS OF THE PHONE

•

BE CAREFUL NOT TO DAMAGE ANY CONTACT SPRINGS

•

NEVER TOUCH THE DISPLAY GLASS

•

USE AIR BLOW EQUIPMENT TO KEEP THE DISPLAY MODULE DUST FREE

Press the On/Off button to turn off the phone.

Check that the memory stick has been removed.

How to open a board-to-board connector with the front
opening tool.

How to open and close a FPC connector (often done with a
dentist hook).

Summary of Contents for K610i






















































Search results

Summary of Contents for K610i

Reviews:

Related manuals for K610i

Brands by name

Popular brands

Sony Ericsson K610i, Working Instructions

Search results

Summary of Contents for K610i

Reviews:

Related manuals for K610i

Brands by name

Popular brands