Sony Ericsson F500 Series Working Instruction, Mechanical Download Page 4

Page: 4 / 43

Working Instruction

Mechanical

3/000 21-1/FEA 209 544/86 E

Company Internal

Sony Ericsson Mobile Communications AB

4(43)

Step-by-Step Instructions

NOTE!
Be careful not to scratch the frame with the
opening tool.

Picture of the Snap opening tool NTZ 112 544.

NOTE!
The tool has a chamfer on one side (1). This side
should be directed towards the phone.

Use the Snap opening tool NTZ 112 544 to
separate the frame from the front. Place it as the
picture shows (2).

NOTE!
Do not bend the tool, just push
straight in the arrow direction (3).

If you bend the tool then it will be
destroyed!!

And press hard until they become separated
from each other.

Do the same thing on the other side of the phone
(4).

NOTE!
Be careful not to scratch the frame with the
K700i/front opening tool.

Picture of the new K700i/Front opening tool
NTZ 112 540.

Press (hard) with the K700i/front opening tool
NTZ 112 540 between the front and the frame
(1) until you get a small gap in the upper side of
the phone.

The phone has two “sidehooks” (2) in the frame
– Bend the front little to booth sides so the side
hooks come loose.

NOTE!
Make sure that they (the sidehooks) are fully
open/released.

Summary of Contents for F500 Series












































Search results

Summary of Contents for F500 Series

Reviews:

Related manuals for F500 Series

Brands by name

Popular brands

Sony Ericsson F500 Series, Working Instruction, Mechanical

Search results

Summary of Contents for F500 Series

Reviews:

Related manuals for F500 Series

Brands by name

Popular brands