background image

5

Instruction for use | Superaqua 1

2. Security

   

 

 

 

Improper installation, pressure tests, modifications or incorrect

 

 

 

operation can cause personal injury and damage to property. 

 

 

 

Pressure surges in the pipeline can damage the meter! 

 

 

 

Existing air pockets falsify the measuring result. 

 

If the seal is damaged or removed, the water meter is no longer approved for legal metering  

     legal measurement. 

 

Before installation, check water meter for transport damage.

 

 

Do not drop, never hold on to the protective cover or the counter.

 

 

If the water meter has been dropped, it must not be installed again.

 

 

Only use suitable lubricants for EPDM seals. 

 

Water meters may only be installed after a pressure test. 

 

Water meters may only be installed in pipelines that have already been leak-tested, rinsed and 

 

     must be well vented before commissioning.  

 

Ensure that the water meter is always fully filled with water.

 

2.1 Personnel qualification

The water meter may only be installed or replaced by qualified personnel for sanitary, heating and 

air-conditioning technology.

2.2 Intended use 

 

 

 

Water meters are used for recording the consumption of drinking water,  

 

 

 

depending on the design for cold or hot water. Other applications that  

 

 

 

differ from these specifications must be approved in writing by Sontex  

   SA.

 

 

 

 

Water meters are exclusively intended for the above-mentioned       

 

                              purpose.  Any other use or modification of the water meters beyond this 

 

 

 

purpose is considered improper and is not permitted. 

   

 

 

 

Warranty only after proven compliance with these regulations and the  

   applicable 

technical 

rules.

 

 

For the period of use, observe all valid national legal regulations 

 

     in particular the calibration regulations. 

 

During installation, observe all specifications according to DIN EN 806 and DIN 1988, in 

     particular hygiene regulations and ambient temperatures. 

 

Observe the nominal operating conditions according to the type examination certificate and the  

     information on the devices. 

 

Keep these instructions with the measuring device

 

Summary of Contents for SQ1M



















Reviews: