Sonnet Fusion QR User Manual Download Page 14

Specifications 

External Connectors

USB 3.0, eSATA, two FireWire 800

Drives Supported

Up-to-date compatible hard drives 

listed on our Certified Hard Drive 

Compatibility Chart

Data Transfer Speed

Up to 250 MB/s, depending 

on interface used and drive 

configuration

Supported Drive 

Configurations

Hardware-based RAID 0, 10, 5, 

Spanned, and JBOD

(1)

Power Adapter

Universal 90W, 100–240V AC, 

50–60Hz

Operating Temperature

32˚ F to 95˚ F  

(0˚ C to 35˚ C )

Dimensions WxDxH

5.93 x 9.57 x 7.76 in.  

(15.1 x 24.3 x 19.7 cm)

RoHS Compliant

Yes

Package Contents

• Desktop disk enclosure

•  Four 3.5" drive trays

• One locking eSATA data cable

• One USB 3.0 cable

• One FireWire 800 cable

• Power adapter

• Power cord

• Tube of threadlocker

• Drive mounting screws

• User’s guide

 
1.  When connected via eSATA, JBOD configuration requires the 

use of an eSATA controller with port multiplier support.

Warnings

Always follow the basic warnings listed here to avoid the risk of 
serious injury or death from electrical shock, short-circuiting, fire, 
and other hazards. These warnings include, but are not limited to:

•  With the exception of the user-swappable parts, do not attempt 

to disassemble or modify the enclosure. If this device appears to 
be malfunctioning, contact your reseller or local distributor.

•  Do not drop the enclosure or any of its drive modules; 

dropping or mishandling of the enclosure or drive modules 
may result in a malfunction.

•  Do not insert your fingers or foreign objects inside the enclosure; 

take particular care when small children are present.

•  Do not expose the device to rain, use it near water or containers 

that contain liquids which might spill into any openings, or in 
damp or wet conditions. 

7 – Specifications, Warnings, and Additional Information

•  If unusual smells, sounds, or smoke come from the device, or if 

liquids enter it, switch it off immediately and unplug it from the 
electrical outlet. 

•  Follow the instructions in this manual carefully; contact your 

reseller or local distributor for additional advice not covered in 
this User’s Guide. 

FCC Compliance 

Fusion QR complies with Part 15 of the FCC Rules. Operation 
is subject to the following two conditions: This device may not 
cause harmful interference, AND this device must accept any 
interference received, including interference that may cause 
undesired operation.

Contacting Customer Service

The Sonnet Web site located at www.sonnettech.com has the 
most current support information and technical updates. Before 
you call Customer Service, please check our Web site for the latest 
updates and online support files, and check this User’s Guide for 
helpful information. 

When you call Customer Service, have the following information 
available so the customer service staff can better assist you:
• Product name 
• Date and place of purchase 
• Computer model 
• Hard drive models
• Operating system version 
• Software/firmware versions

USA Customers

 

If further assistance is needed, please contact 

Sonnet Customer 

Service

 at:

  

Tel

: 1-949-472-2772  

(Monday–Friday, 7 a.m.–4 p.m. Pacific Time) 

E-mail

[email protected]

For Customers Outside the USA

 

For support on this product, contact your reseller or local 
distributor. 

Visit Our Web Site

For the most current product information and online support 
files, visit the Sonnet Web site at www.sonnettech.com/support/. 
Register your product online at http://registration.sonnettech.com 
to be informed of future upgrades and product releases.

©2014 Sonnet Technologies, Inc. All rights reserved. Sonnet, the Sonnet logotype, Simply Fast, the Simply Fast logotype, Creativity Stored Here, and Fusion are trademarks of Sonnet Technologies, Inc. FireWire, Macintosh, 
Mac, the Mac logo, and OS X are trademarks of Apple Inc., registered in the United States and other countries. Other product names are trademarks of their respective owners. Product specifications subject to change 
without notice. Printed in the USA. UG-FUS-DE4Q-0TB-E-B-050814

Summary of Contents for Fusion QR















Reviews: