Sonifex Redbox RB-DMX4 User Handbook Manual Download Page 14

2

Redbox RB-DMX4 User Handbook

INTRODUCTION

INTR

ODUC

TION

1

Auto Lock Mode
The digital output sample rate follows the sync input. If the sync signal is removed then the 
output sample rate will be set by, and locked to, the internal on-board clock generator at 
the closest frequency available to the previous sync input.

Slave Mode
In this mode the digital output sample rate follows the sync input. When the sync signal is 
not present the digital output is turned off. 

There is a monitor socket on the front panel with a gain pot to allow you to monitor the 
output of each channel. The monitored channel can be selected via a push button on the 
front panel which, when held, can  also supply up to 12dB of gain. If the level that is being 
monitored is close to full scale, a 12dB attenuation can be added to the monitor channel 
via a DIPswitch on the rear panel.  

The unit can be placed in mono or stereo mode via rear panel DIPswitch. Stereo mode 
allows you to monitor the two input pairs as stereo channels as well as controlling the 
input gain as a pair, giving tied audio levels. 

The RB-DMX4 has been designed to have a passive signal path through the main input, so 
if power to the unit fails, signal inputs 1 & 2 are routed to outputs 1 & 2 and signal inputs 
3 & 4 are routed to outputs 3 & 4. This is essential for applications such as installation at 
transmitter sites, where a power failure to the unit should not prevent the audio input 
signal from being output to the transmitter. Please note that this is not true for the TOSLink 
outputs which are muted.

The RB-DMX4 can be controlled using Sonifex free software, SCi. Contact Sonifex for further 
information if you have a particular requirement that isn’t catered for by the RB-DMX4 as 
standard.

Fig 1-2: RB-DMX4 System Block Diagram 

S/PDIF

S/PDIF

Optical
AES

Optical

S/PDIF

Freq Select

AES Sync

Word Clock

Video Optional

Digital Source

Select

Digital Input 1

Digital Input 2

Clock

Select

Master

Clock

Generation

VID RX

AES RX

WC RX

AES

RX

SRC

AES

Optical

S/PDIF

RX

SRC

DSP

Digital Output 2

Digital Output 1

AES

Optical

TX

TX

Power

Failure

Relay

Power

Failure

Relay

Summary of Contents for Redbox RB-DMX4





































Reviews: