manualshive.com logo in svg

Sonifex Redbox RB-DEDD8, User Handbook Manual

Share
Download
Sonifex Redbox RB-DEDD8 User Handbook Manual Download Page 36

24

Redbox RB-DEED8 & RB-DEDD8 User Handbook

SCI

SCI

2

Front Panel Lock

When selected, this control disables the front panel and prohibits any changes to be made 
via the front panel.  This control is automatically disabled when the unit is powered on.

Network

This displays the current settings and status of the network connection on the unit.

Enable DHCP: This enables the unit to receive it’s IP address, subnet mask and gateway

settings from a DHCP server. If one is not available then this should be disabled through

the serial port and a valid static address be entered.  This option cannot be set via SCi and 
must be set via the front panel of the unit.

Selecting the CURRENT page displays the network address in use by the unit.

IP Address: Displays the current IP address of the unit  (this is also displayed on the bottom 
of the screen). If DHCP is enabled then this will normally be the IP address supplied by the 
DHCP server.

Subnet Mask: Displays the current subnet mask for the unit.

Default gateway: Displays the current default gateway for the unit.

MAC Address: The unit’s MAC address. This cannot be changed.

Selecting the STATIC page displays the static network address stored in the unit.  This 
address is used when the DHCP is disabled.

Note: 

The units are discovered using broadcast packets. If your PC has two network cards, 

then there is a limitation in windows that requires the two addresses to be on different 
subnet addresses.

Summary of Contents for Redbox RB-DEDD8





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands