Sonance Sonamp 875D SE Instruction Manual Download Page 7

7

SONAMP

®

875D SE 8-CHANNEL AMPLIFIER

Protection Circuits

Thermal Protection

If the amplifier’s cooling vents are blocked, or it is installed with inadequate ventilation the amplifier may
exceed its safe operating temperature. If the amplifier’s internal temperature exceeds 154°F (68°C) it
will self-protect, and the following will occur:
• The audio output to all connected zones will shut OFF.
• The front-panel P

ROTECTION

LEDs (see 

Figure 3) will illuminate yellow.

• An over-temp message will be sent via RS-232.
Once a safe temperature (<67°C) is reached, the Protection LEDs will all extinguish. You can then 
re-activate the amplifier, either by switching the front-panel Power button OFF and ON or by a ‘Power’
command if the amplifier is being serial controlled.

IIM

MPPO

ORRTTAAN

NTT::   BBeeffoorree   rree-aaccttiivvaattiinngg   tthhee   aam

mpplliiffiieerr,,   ccoorrrreecctt   tthhee   pprroobblleem

m   tthhaatt   ccaauusseedd   tthhee

oovveerr-tteem

mppeerraattuurree ccoonnddiittiioonn  ((vvoolluum

mee  sseett  ttoooo  hhiigghh,,  iinnaaddeeqquuaattee  vveennttiillaattiioonn,,  eettcc..))  

NOTE: If you’re serial-controlling the 875D SE you can poll the amplif ier at any time and its internal

temperature will be repor ted to the control device.

Over-Current Protection

If an over-current condition occurs in a zone, that zone will shut OFF for 5 seconds and its P

ROTECTION

LEDs will flash ON

and OFF. The zone will then turn back ON. If the over-current condition continues the zone will shut OFF for 6 seconds,
its P

ROTECTION

LEDs will flash, then it will turn back ON. If the over-current condition continues this process will repeat,

with the wait time increasing by 1 second each time. When the wait time reaches 10 seconds the zone will LOCK, the
zone’s P

ROTECTION

LEDs will continually illuminate and the amplifier must be powered OFF using the front-panel P

OWER

button (or a serial command, if the amp is being controlled via RS-232). BB ee ff oo rr ee    tt uu rr nn ii nn gg    tt hh ee    aa m

m pp ll ii ff ii ee rr    O

O N

N    aa gg aa ii nn ,,   

cc oo rr rr ee cc tt    w

w hh aa tt ee vv ee rr    ii ss    cc aa uu ss ii nn gg    tt hh ee    oo vv ee rr -- cc uu rr rr ee nn tt    cc oo nn dd ii tt ii oo nn    ii nn    tt hh ee    zz oo nn ee    (( ss pp ee aa kk ee rr    ii m

m pp ee dd aa nn cc ee    tt oo oo    ll oo w

w ,,    vv oo ll uu m

m ee    tt oo oo

hh ii gg hh ,,    ss hh oo rr tt -- cc ii rr cc uu ii tt ,,    ee tt cc .. )) ..

PROTECTION

BBE ON

ACTIVE

Figure 3: 

F

RONT

-P

ANEL

S

TATUS

LEDs

Summary of Contents for Sonamp 875D SE





























Reviews: